background image

Reference Manual 
 
Capacitor Bank Protect. Relay KSR1 

 

Rev. 10 

 

 

2018-09 

 

16 

 

The KSR1 uses absolute values. For this reason, shown values are always positive independent of their actual 

direction (meas. value increases / decreases). 

 

 

Digital input active 

 

  the monitoring system can be blocked via the digital input. 

 

  

the monitoring system cannot be blocked via the digital input. 

 

  Digital input open or closed 

  monitoring system is blocked when terminals DI1 & DI2 are closed. 

 

monitoring system is blocked when terminals DI1 & DI2 are open. 

 

 

Attention: The digital input is activated or deactivated by opening or closing the contact DI1 and DI2. Connecting 

a voltage signal can destroy the KSR1. 

 

4.2.2.4

 

 Reset menu 

  reset trip 

  reset alarm 

  reset stored alarms and trips 

  reset natural unbalance 

 

 

reset the device to factory settings. 

 

change password “setup”. Possible adjustment 000-999. Master password 242. 

 

change password “expert”. Possible adjustment 000-999. Master password 511. 

To switch off the password protection, set 

 to 000. 

Содержание KSR 1























Отзывы: