background image

Reference Manual 
 
Capacitor Bank Protect. Relay KSR1 

 

Rev. 10 

 

 

2018-09 

 

15 

 

4.2.2.3

 

 Alarm menu 

 

Trip active 

 

  When  exceeding  the  adjusted  threshold  for  trip,  the  trip  relays  switches  and  the  message

 blinks on the display. 

 

 

An exceeding of the trip threshold is ignored. 

 

  Store trip in “Alarm buffer” 

 

  Trips are stored with the trigger value in the “Alarm buffer”. 

 

  

Trips are not stored. 

 

 

Alarm active 

 

  When  exceeding  the  adjusted  threshold  for  trip,  the  trip  relays  switches  and  the  message 

 blinks on the display. 

 

  

An exceeding of the trip threshold is ignored. 

 

  Store alarm in “Alarm buffer” 

 

  Alarms are stored with the trigger value in the “Alarm buffer”. 

 

  

Alarms are not stored. 

 

  Drop off ratio (hysteresis) 

It is possible to set the hysteresis to 50% – 100% of the adjusted thresholds for current and voltage. The “drop off ratio” 

defines the threshold, which resets a trip or an alarm when the measured value falls below the adjusted threshold.  For 

example: 

Case 1: Threshold for trip is 0.5 A and “drop of ratio” is 100% => trip is reset when the current falls below 0.5 A.  

Case 2: Threshold for trip is 0.5 A and “drop of ratio” is 50% => trip is reset when the current falls below 0.25 A. 

 

Содержание KSR 1























Отзывы: