manualshive.com logo in svg

Belmont Bel-Nova AL-D101G, Руководство по установке

Поделиться
Скачать
Belmont Bel-Nova AL-D101G Скачать руководство пользователя страница 23

(3) Attach the light assembly to the ceiling pole 
1. Be sure the ceiling pole is plumb. Adjust vertical level 
    of the ceiling pole with leveling flange nuts (M8) and 
    secure ceiling flange to flange base with fixing hex 
    nuts (M8).

2. Slide the flange cover and flange cover ring (flat side 
    up) over the ceiling pole and secure them about half 
    way up the pole. Use only one set screw as you will be 
    moving the on final installation.

3. Install the light assembly to the ceiling pole running 
    the 3 wires cord up through the pole to the ceiling 
    flange.

    Secure it with 4 hexagonal set screws (M5 x 10, plated). (Be 
    careful not fall off the light assembly.)

4. Connect the incoming power to the 3 wires cord from 
    the light assembly.

    Be sure to follow the local electrical codes.

5. Reposition the flange cover and secure it with the 
    flange cover ring. 

    Secure three hexagonal set screws (M6 x 8, plated).

Ceiling pole

Ceiling flange

Hexagonal set screw
(M5 x 10, plated)

Flange cover

Flange cover ring

Hexagonal set screw
(M6 x 8, plated)
(With red mec thread lock)

Hex nut
(M8, plated)

Flat washer
(M8, plated)

Spring washer
(M8, plated)

Flange nut
(M8, plated)

3    Installation

23

Содержание Bel-Nova AL-D101G

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды