manualshive.com logo in svg

Belden Grass Valley HDA-1911, Руководство по установке и эксплуатации

Поделиться
Скачать
Belden Grass Valley HDA-1911 Скачать руководство пользователя страница 8

GUIDE TO INSTALLATION AND OPERATION 
 

8

  |  HDA-1911/1931 

 

The rear connector panel must be installed with the card out of the frame. 
 

 

To remove an existing card from the slot, tilt up the swivel handle on the front of the card to lever the connectors 
apart, then use the handle to pull the card straight out of the slot.

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

 

Densité-2 frame 

– rear panel installation 

Densité-3 frame 

– rear panel installation 

 

To install the connector panel: 
 

(NOTE - if you are installing a Densité-2 rear panel plus adapter in a Densité-3 frame, please go to section 2.3) 

 

1.  If a card is installed in the slot whose rear panel is being changed, remove it as described above. 

 

2.  Remove the existing panel (either blank or belonging to an existing card that is being changed) by releasing the 

captive screw(s) at the bottom. 

 

3.  Position the new panel and secure it in place with the captive screw(s) at the bottom. 

 

2.2  Card Installation 

 
Once a matching rear connector panel has been installed, install the HDA-19x1 card as follows: 
 

1.  Open the front panel of the frame. 

 

2.  Slide the HDA-19x1 card into the slot and push gently on the handle to seat the connectors.  

 

If the card is used with a double-width rear panel (DRP), it should be inserted into the right-hand slot. Inserting 
the card into the wrong slot will not damage the card, and will be flagged by the on-card status LED flashing red 
to indicate that there is no connection to the rear panel. 

 

3.  Close the front panel of the frame. 

 

2.3  Installing Densité-2 Cards and Rear Modules in a Densité-3 Frame 

 
The Densité-3 frame supports many Miranda Densité-2 series cards, including the HDA-19x1. Should you wish to 
install the HDA-19x1 card in your Densité-3 frame, you will need an adapter for the card. You may use one of the two 
3 RU rear panels that are available for the HDA-19x1 (3SRP), or you may use one of the eight 2 RU rear panels. In 

Содержание Grass Valley HDA-1911
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды