manualshive.com logo in svg

Belden Grass Valley HDA-1911, Руководство по установке и эксплуатации

Поделиться
Скачать
Belden Grass Valley HDA-1911 Скачать руководство пользователя страница 7

GUIDE TO INSTALLATION AND OPERATION 

HDA-1911/1931  |  

7 

 

2  Installation 

 

2.1  Installation of Rear Connector Panels 

 

Miranda Densité-series cards are each associated with a rear connector panel, which must be installed in the Densité 
frame before the card can be inserted. 
 
The HDA-19x1 card is sized to fit into Miranda

’s Densité-2 frame. Eight different rear connector panels are available 

to fit the Densité 2 frame: 
 

 

HDA-19NN-SRP  

Single rear for 1x4 operating mode. 

 

HDA-19NN-SRP-R 

Single rear for 1x4 operating mode with bypass protection relay. 

 

HDA-19NN-SRP-F 

Single rear for 1x2 operating mode with fiber option support. 

 

HDA-19NN-DRP 

Double rear for 1x9 operating mode. 

 

HDA-19NN-DRP-R 

Double rear for 1x9 operating mode with bypass protection relay. 

 

HDA-19NN-DRP-F 

Double rear for 1x8 operating mode with fiber option support. 

 

HDA-193N-DRP 

Double rear for dual 1x4 operating mode (HDA-1931 only). 

 

HDA-193N-DRP-F 

Double rear for dual 1x3 operating mode with fiber option support (HDA-1931 only). 

 
With the use of an available adapter (Densité 3 

– EXT B), the HDA-19x1 can also be installed in a Densité-3 frame 

(see section 2.3 below). Two rear connector panels for this frame are available for the HDA-19x1:  
 

 

HDA-191N-3SRP 

Single rear for 1x7 operating mode. 

 

HDA-193N-3SRP 

Single rear for dual 1x3 operating mode (HDA-1931 only). 

 
The eight Densité-2 rear panels can also be used in a Densité-3 frame, with the addition of available adapters: 
 

 

HDA-19NN-SRP + DENSITE-SRP-3RU  

Single rear for 1x4 operating mode. 

 

HDA-19NN-SRP-R + DENSITE-SRP-3RU  Single rear for 1x4 operating mode with bypass protection relay. 

 

HDA-19NN-SRP-F + DENSITE-SRP-3RU 

Single rear for 1x2 operating mode with fiber option support. 

 

HDA-19NN-DRP + DENSITE-DRP-3RU 

Double rear for 1x9 operating mode. 

 

HDA-19NN-DRP-R + DENSITE-DRP-3RU  Double rear for 1x9 operating mode with bypass protection relay. 

 

HDA-19NN-DRP-F + DENSITE-DRP-3RU  Double rear for 1x8 operating mode with fiber option support. 

 

HDA-193N-DRP + DENSITE-DRP-3RU 

Double rear for dual 1x4 operating mode (HDA-1931 only). 

 

HDA-193N-DRP-F + DENSITE-DRP-3RU 

Double rear for dual 1x3 operating mode with fiber option 
support (HDA-1931 only). 

 
All cards and rear panels can be installed with the frame power on. The card has connectors which plug into a mid-
frame mother board for distribution of power and for connection to the controller card, and a second connector which 
plugs directly into the rear connector panel for input and output.  
 

 
 
 
 
 
 
 

Содержание Grass Valley HDA-1911
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды