Belarus 1025 2008 Скачать руководство пользователя страница 5

Страница: 5 / 205

Belarus 1025/1025.2/1025.3

Section А.Introduction

Section А. INTRODUCTION

The present operation manual contains major technical data and

recommendations on the operation and maintenance of tractors Belarus

1025/1025.2/1025.3.

Tractors Belarus 1025/1025.2/1025.3 are designed for executing various

agricultural works with mounted, half-mounted and trailing machines and implements,

in transportation, with loading, unloading mechanisms, harvesting complexes and for

driving stationary machines.

Tractor Belarus 1025

– is a base model with engine

-245, rated power of 77

kW (104.6 hp), front drive axle (FDA) of portal type with coned wheel reduction gears,

hydraulic mounting system with power regulator and traction-coupling mechanism

TCM-1J (cross-piece).

Tractors Belarus 1025.2 and Belarus 1025.3 are modifications of the base

model.

Tractor Belarus 1025.2

– with engine

-245 with rated power of 77 kW (104.6

hp), beam-type FDA with planetary-cylindrical wheel reduction gears, hydraulic

mounting system with power regulator and traction-coupling mechanism TCM1J

(cross-piece), or hydraulic lift and lift-type TCM with yoke TCM-3V.

Tractors Belarus 1025 and Belarus 1025.2 can be equipped (optionally) with

engine

-245S with rated power of 79 kW (107.3 hp), certified according to the 1st

stage of Directive 2000/25

ЕС

Tractor Belarus 1025.3

– with engine

-245S2 has rated power of 81 kW

(110.0 hp), beam-type FDA with planetary-cylindrical wheel reduction gears, hydraulic

mounting system with power regulator and traction-coupling mechanism TCM-1J

(cross-piece), or hydraulic lift and lift-type TCM-3 (yoke). Updated design of the cabin

and hood. Engine

-245S2 is certified according to 2

stage of Directive 2000/25 EC.

ATTENTION!

Prolonged and reliable tractor operation is possible only if

proper operation and timely maintenance are observed

ATTENTION!

Before putting new tractor into operation study the present

operation manual and strictly follow recommendations thereof, to avoid accidents,

injures or mutilations.

Note:

Reference in the present manual text made to “left-side” or “right-side”

are made from the view of the observer standing behind the running tractor.

Note:

Due to constant tractor update and improvement of working conditions,

changes, not indicated in the present edition, may be introduced to the tractor

design.

Re-equipment and alteration of tractor design without approval of the

manufacturer are forbidden.

Содержание 1025 2008














































































































































































































Результаты поиска

Содержание 1025 2008

Отзывы:

Похожие инструкции для 1025 2008

Бренды по названию

Популярные бренды

Belarus 1025 2008, Руководство по эксплуатации

Результаты поиска

Содержание 1025 2008

Отзывы:

Похожие инструкции для 1025 2008

Бренды по названию

Популярные бренды