Beko BEKOMAT 14i Скачать руководство пользователя | Manualshive

Страница: 6 / 76

background image

2. Safety

2.1 Use

The

BEKOMAT

®

14i / 14i CO / 14i CO PN25

, also referred to as product or

BEKOMAT

®

below, has been designed for

draining condensate from low pressure systems and pressureless vacuum systems. The

BEKOMAT

®

is able to drain

condensate at operating pressure with no pressure loss.

2.1.1 Intended use

Any use of this system other than the use described in this manual is hereby deemed to be non-intended and can cause a
hazard for the safety of people and the environment.
The following must be noted for intended use:
•  Read and follow the manual.
•  Only use the product and the accessories in indoor areas.
•  Only use the product and accessories within the operating parameters given in the technical data and the agreed

delivery conditions.

•

Only use the product and accessories with media which are free of caustic, aggressive, corrosive, toxic, flammable,

oxidising or inorganic components.

• In cases of doubt an analysis must be carried out.
• Only use the product and accessories in surroundings where splash water is the maximum possible water exposure

that can occur. The splash water must be free of corrosive components.

• Only use the product and accessories in areas which are free of toxic and corrosive chemicals and gases.
• Only use the product and accessories within the piping system designed for the technical data with appropriate

connections, pipe diameters and assembly clearances

• Only use the product and accessories outside potentially explosive atmospheres.
• Only use the product and accessories away from direct solar radiation and heat sources as well as areas subject to

frost.

• Only combine the product and accessories with the products and components named and recommended by

BEKO

TECHNOLOGIES in the manual.

• Adhere to the prescribed maintenance schedule.

Before using the product and the accessories, the operating company must make sure that all conditions and
prerequisites for intended use are given.

The product and the accessories have been exclusively designed for stationary use in a commercial or industrial area. All
of the assembly, installation, operation, maintenance, disassembly and disposal work described may only be performed

by qualified skilled technical personnel.

BEKOMAT

®

14i / 14i CO / 14i CO PN25

Original installation and operation manual

6 | 76

«
...
4
5
6
7
8
...
»

Содержание BEKOMAT 14i













































































Отзывы:

Нет отзывов

Похожие инструкции для BEKOMAT 14i

Whatman Mini-UniPrep G2

Бренд: GE Страницы: 28

Бренд: Pure Water Technology Страницы: 25

Бренд: Pelican Страницы: 15

Бренд: Watts Premier Страницы: 28

Star Celeste S140

Бренд: Tyco Fire Product Страницы: 4

Бренд: Watts Страницы: 38

Бренд: BWT Страницы: 12

tyco DS-1 Series

Бренд: Johnson Controls Страницы: 10

Three Stage Reverse Osmosis

Бренд: Hydrofarm Страницы: 4

Бренд: Waterite Страницы: 24

PRESSURE-FLO PT1500

Бренд: laguna Страницы: 19

Бренд: Trox Technik Страницы: 5

Бренд: Craftsman Страницы: 16

Бренд: Kenmore Страницы: 12

Бренд: Kenmore Страницы: 20

Бренд: Kenmore Страницы: 12

Бренд: Kenmore Страницы: 12

Бренд: Kenmore Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды