Beko BEKOMAT 14i Скачать руководство пользователя страница 24

Страница: 24 / 76

3.5.3.4 Control commands

The forwarding of control commands to the product is described below.

Control command

Control-Holding-Register

(Modbus Specification)

Description / explanation

Hex.

Dec.

Command

Value

Beacon on

0x1770

6000

0x0001

All the LEDs of a certain device flash at

the same time to identify this device.

Beacon off

0x1770

6000

0x0000

End flashing of the LEDs.

Valve control, start

0x1771

6001

time

Start the discharge process for a given
time in milliseconds.

Maximum possible duration of
the entry: 65000 ms.

Valve control, end.

0x1771

6001

0x0000

Stop the discharge process.

Service interval, time

0x1772

6002

0x0001

Reset the time until the next
maintenance.

Service interval, switching
cycles

0x1772

6002

0x0002

Reset the switching cycles until the next
maintenance.

Restart device

0x1773

6003

0x8E40

Restart the device.

1. Write the value 0xBEEF (decimal: 48879) to the Key Register 0x1392 (decimal: 5010).

Write access and control command function are released for 1 minute.

2. Select the control command from the control command table and write it to the respective Control Holding Register.
Example: Reset the time until the next maintenance

Register

Value

Control-Holding-Register:

0x1772 (dec. : 6002)

Command Value:

0x0001

3. After the values have been entered in the Control Holding Register, the release of write access and the control

command function expires.

3.5.4 Error messages

Error code Error message

Description / explanation

ILLEGAL FUNCTION

Function not implemented

ILLEGAL DATA ADDRESS

Requested address outside of the valid range

ILLEGAL DATA VALUE

Incorrect data

SERVER DEVICE FAILURE

Error occurred during inquiry that cannot be eliminated

BEKOMAT

14i / 14i CO / 14i CO PN25

Original installation and operation manual

24 | 76

Содержание BEKOMAT 14i













































































Результаты поиска

Содержание BEKOMAT 14i

Отзывы:

Похожие инструкции для BEKOMAT 14i

Бренды по названию

Популярные бренды

Beko BEKOMAT 14i, Руководство пользователя

Результаты поиска

Содержание BEKOMAT 14i

Отзывы:

Похожие инструкции для BEKOMAT 14i

Бренды по названию

Популярные бренды