Beko BEKOMAT 14i Скачать руководство пользователя | Manualshive

Страница: 23 / 76

background image

3.5.3.3 Changing interface parameters

INFORMATION

BEKO TECHNOLOGIES configuration tools!

i

BEKO

TECHNOLOGIES recommends using the Software Integrator to change the interface

parameters. The software can be downloaded from the

BEKO

TECHNOLOGIES homepage

(see “1.1 Contact” on Page 5).
For connection to a PC, BEKO TECHNOLOGIES recommends using the
Integrator Hardware Kit (for ordering information see chapter “11.2 Accessories” on Page
61).

This process is used to change interface parameters required for communication.

1. Write the value 0xAC1D (decimal: 44061) to the Holding Register 0x1392 (decimal: 5010).
2. Write the parameter to the Holding Register 0x07D0 (decimal: 2000).

Description / explanation

HighByte:

See the following table

LowByte:

Modbus Client address 1 … 246

Example value:

0x070A (decimal: 1802)
For interface parameters see table Index 0x07 (decimal: 7)
Client address 0x0A (decimal: 10)

3. To save the settings write the value 0xBA5E (decimal: 47710) to the Holding Register 0x139C (decimal: 5020).
4.

Switch the product off and switch it back on again.

0

The changes will go into effect approx. 10 seconds after the restart.

Parameter - HighByte

Parameter - HighByte

Selection

Baud rate

[Bd]

Parity

Stop Bit

Selection

Baud rate

[Bd]

Parity

Stop Bit

0x00

4800

No

2

0x0C

57600

No

2

0x01

4800

Even

1

0x0D

57600

Even

1

0x02

4800

Odd

1

0x0E

57600

Odd

1

0x03

9600

No

2

0x0F

76800

No

2

0x04

9600

Even

1

0x10

76800

Even

1

0x05

9600

Odd

1

0x11

76800

Odd

1

0x06

19200

No

2

0x12

115200

No

2

0x07

19200

Even

1

0x13

115200

Even

1

0x08

19200

Odd

1

0x14

115200

Odd

1

0x09

38400

No

2

0x0A

38400

Even

1

0x0B

38400

Odd

1

Original installation and operation manual

BEKOMAT

®

14i / 14i CO / 14i CO PN25

23 | 76

«
...
21
22
23
24
25
...
»

Содержание BEKOMAT 14i













































































Отзывы:

Нет отзывов

Похожие инструкции для BEKOMAT 14i

Бренд: Galcon Страницы: 20

Бренд: Watermaid Страницы: 38

CLEARLINE CL-990-X1.5

Бренд: ELECTROSEA Страницы: 20

Бренд: Premier Страницы: 8

HIGH PRESSURE FILTER KIT

Бренд: DH Instruments Страницы: 1

Бренд: NEXT pool Страницы: 19

Бренд: WaterChef Страницы: 12

Bell & Gossett NRF-25

Бренд: Xylem Страницы: 20

Бренд: Acuva Страницы: 40

Бренд: LG Страницы: 32

MULTI V HYDRO KIT ARNH423K2A4

Бренд: LG Страницы: 111

Premium 5231JA2002A-S

Бренд: LG Страницы: 2

Бренд: LG Страницы: 36

Бренд: LG Страницы: 20

Бренд: LG Страницы: 36

Бренд: LG Страницы: 36

Бренд: LG Страницы: 36

Бренд: Oase Страницы: 117

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды