Beijing Starfire Control Technology Co.,Ltd.
北京斯达峰控制技术有限公司
Model SF-2012AH-QG
Cutting Machine
（
C002
）
22
NO-PRE SHAPE(0/1)
----
No need to display the drawing when processing, choose 1.
X-axis width of steel plate ----
The actual width of steel plate along X axis, which is enabled only in running extra large
program.
Y-axis height of steel plate ----
The actual height of steel plate along Y axis, which is enabled only in running extra large
program.
Common edge option
——
Since the system may control three kinematic axes, this option is used to determine the 3rd axis(Z
axis) shares a common edge with X axis or with Y axis for the machine requiring double-edge drive. Take 0 to have Z axis and X axis
share a common edge; take 1 to have Z axis andYaxis share a common edge.
Metric/English system option
——
Take 0 for metric system, which will have length parameters, speed parameters and values
as well as coordinates expressed in metric unit(mm), though it supports machining program in English system(G20). Take 1 for English
system, which will have parameters, display and coordinates expressed in English unit (inch), though it supports machining program in
metric program(G21).
CALCULATE PRECISION
—— When programming, some nesting software produces some burrs. We can solve the problem after
setting this parameter, the default value is 0.1 mm.
CONTROLOUTSIDE (0/1)
—— If you use a remotecontrol then select 1, otherwise select 0.
WIRED-0/WIREDESS-1 CTRL(0/1
）
—— If remote control is wired control ,then select0, otherwise, select 1.
G41/G42 CHECK EFF(0/1)
—— There is correct check to the compensation in the system ( G41/G42 ) .When the error is not serious,
this parameter should be selected 0, prompting an error, but there is no alarm, the program can continue to run.
INITIALCLEAR COOR
（
0/1
）
—— select 1
，
before processing, Coordinate will be automatically cleared to 0.Wentai does not have
G92
，
so it needs this function.
SELECT CYLINDER UP/DOWN(0/1)
——in sheet metal processing, cylinder is more effective than THC, SELECT 1, otherwise,
select 0.When cylinder is selected, M16 is valid when the torch moves down ,M16 is invalid (canceled) when the torch moves up.
SELECTAUTO-REFERENCE
（
0/1
）
—— Select 1, return to the reference point after finishing processing automatically.
LIMITPOSI EFFECT
（
0/1
）
——Many small cutting machines don’t have limit switch outside for their simple structure, then we can
select [SETUP]- [CONTROL] - LIMIT POSI EFFECT = 0, in order to avoid unnecessary limit alarm failure.
SOFTWARE LIMITEFFECT
（
0/1
）
—— Select 1, software limit function is in effect.
Note: when collision detection is being used, hardware limit function must be canceled.
COLLIDE-LOCATE SAME PORT
（
0/1
）
- Whether collision detection and location detection have a same input port.
COLLIDE PAUSE(0)/TORCHUP
（
1
）
- Select 0, processing will stop when collide happens, select 1, the torch will move up
automatically when collide happens and processing will continue.
PAUSE UPTORCH
（
0/1
）
——If want an action of torch up after pause ,select 1.
BRIDGE CUTOFF LINE(MM)
—— After setting bridge point, re-start cutting after moving this much distance (Equivalent to
bridge width).
DISPLAYINFORMATION
（
0/1
）
（
SF-2100AH
）
- Whether display the company and system information when the controller is on or
not.
DISPDENSITY
（
0/1/2
）
（
SF-2012AH
）
- Select the fineness of processing shapes.
SELE PLOTKERFLINE
（
0/1
）
- Whether to display the coordinate trajectory, when there is kerf compensation or not.
Attention: Please be cautious to make any change if no idea of the specific
application of a parameter!
