Beijing StarFire Control Technology Co., Ltd. SF-2012AH-QG Скачать руководство пользователя страница 13

Страница: 13 / 61

Beijing Starfire Control Technology Co.,Ltd.

北京斯达峰控制技术有限公司

Model SF-2012AH-QG

Cutting Machine

（

C002

）

Fig. 3.2 ASSI window

3.2.7. [F3] ROTATE(steel plate correcting feature)

3.2.7.1Machining at rotation angle

This feature is used when the steel plate is not positioned perfectly or the steel plate needs to rotate an angle

before machining. It is allowed to use

Rotate

function along with

BEG. PT.

and

END PT.

Manual

mode or

input the expected angle directly. After acknowledged, the system will start the machining program at the

appointed rotation angle.

Note: Counterclockwise direction is taken as positive angle.
3.2.7.2Example

The system is able to identify and calculate the rotation angle by measuring the origin point and the end point

ESC

CONTOU

WENTAI ROTATE MIRR

SCALE

NEST

BRAKE

Содержание SF-2012AH-QG






























































Результаты поиска

Содержание SF-2012AH-QG

Отзывы:

Похожие инструкции для SF-2012AH-QG

Бренды по названию

Популярные бренды

Beijing StarFire Control Technology Co., Ltd. SF-2012AH-QG, Руководство пользователя

Результаты поиска

Содержание SF-2012AH-QG

Отзывы:

Похожие инструкции для SF-2012AH-QG

Бренды по названию

Популярные бренды