Beijing StarFire Control Technology Co., Ltd. SF-2012AH-QG Скачать руководство пользователя страница 11

Страница: 11 / 61

Beijing Starfire Control Technology Co.,Ltd.

北京斯达峰控制技术有限公司

Model SF-2012AH-QG

Cutting Machine

（

C002

）

Flame machining case:

rise the cutting torch(M72), open the cutting oxygen(M12) and lower the

cutting torch(M73).

Plasma machining case:

execute

Ｍ

07 command.

Note:

This is a very important feature. It will be used repeatedly in pause, return and extend piercing

operations. When preheat is done, pressing [PIERCE] key will start up piercing operation

directly.

[SWOFF]: To shut off all the heavy-current output.

[

Ｓ

↑]: Push it down to rise the cutting torch and release to stop the torch.

[

Ｓ

↓]: Push it down to lower the cutting torch and release to stop the torch.

；

3.1.8[1] BLOWUP

The pattern will be magnified one times by one keystroke and it can be magnified to eight times

maximum by

three keystrokes.

3.1.9 [2] RESTIT

To restore to normal pattern size.

3.1.10 [X] TEST

If [X] key is pressed, the system will run the program at top speed without executing

Ｍ

command. This

feature is often used to position quickly or check the working size of steel plate. This operation can be paused at any

moment or cancelled by pressing [X] key one more times.

3.1.11 [Y] AU-SPD

Since the manual speed and automatic speed is separate in the system, this key is used to switched between

automatic mode and manual mode to adjust the speed multiplying factor.

3.2. Function selection inAUTO mode

It is allowed to invoke a machining program by means of

EDIT

feature. If a program has been invoked(as long as it is the same

program name), it can be run directly. If the program is invoked from an USB disk, especially a large program, it can be run directly with

USB disk connected instead of saving it into the system.

3.2. 1[F1] SECTION

To assign system to start up machining operation from any section or piercing point.

It is often used when machining needs to start from a certain section or only a part needs being processed.

Refer to

SECTION

feature for details.

3.2.2[F2] MAN

To switch the system to manual mode.

3.2.3[F3] RESBREK

After this function is selected, pressing [

START

] key to fulfill breakpoint restoration. Refer to

RESBREK

feature for details.

Содержание SF-2012AH-QG






























































Результаты поиска

Содержание SF-2012AH-QG

Отзывы:

Похожие инструкции для SF-2012AH-QG

Бренды по названию

Популярные бренды

Beijing StarFire Control Technology Co., Ltd. SF-2012AH-QG, Руководство пользователя

Результаты поиска

Содержание SF-2012AH-QG

Отзывы:

Похожие инструкции для SF-2012AH-QG

Бренды по названию

Популярные бренды