AC Power Connections
Power Cord
Power Cord
From AC Mains
El dispositivo de iluminación usa un receptáculo de conexión de alimentación IEC con un fusible interno.
PRECAUCIÓN:
Asegúrese de que el diferencial del sistema de alimentación esté desactivado antes de realizar cualquier conexión a la corriente eléctrica.
Asegúrese de que el amperaje total de todas las unidades no sobrepase la capacidad máxima de la salida de corriente.
No utilice esta unidad con dimmers
La fuente de alimentación debe disponer de toma de tierra, y la conexión a la corriente a este sistema de iluminación debe usar un cable
de alimentación de 3 filamentos.
Desconecte la unidad de la corriente antes de realizar cualquier comprobación o sustituir el fusible interno.
Control del dispositivo
Este dispositivo puede ser controlado de las siguientes formas:
1. De forma independiente (modo “Stand Alone”)
2. En un esquema máster/esclavo
3. Control DMX
4. Control remoto por infrarrojos (IR)
De forma independiente (Stand Alone)
Puede usar este dispositivo por sí solo, sin ningún controlador DMX
1. Use el menú
AUTO
para elegir entre 3 modos de show automático diferentes
2. Use el menú
STRO
para elegir entre 20 shows estroboscópicos
3. Use el menú
DERB
para elegir una frecuencia estroboscópica y un color personalizado para el efecto Derby
4. Use el menú
SOUN
para elegir la activación por sonido de los shows internos
Control máster/esclavo
1. Conecte este dispositivo(s) con un cable(s) DMX tal como puede ver en la sección de control DMX.
Nota: De cara a evitar interferencias, conecte 32 unidades a la vez como máximo.
2. Ajuste de la unidad máster o controladora:
2.1. Pulse
MENU
en el primer dispositivo
2.2. Pulse
ENTER
2.3. Use
UP
y
DOWN
para elegir
MAST
2.4. Pulse
ENTER
(ahora la primera unidad será la máster o controladora)
2.5. Pulse
MENU
y elija cualquiera de los modos
AUTO, STRO, DERB, SOUN
2.6. Pulse
ENTER
2.7. Después de unos 5-10 segundos de inactividad, el modo de show será activado
Control del Dispositivo
IR Remote Control
When using the remote control, the space between the device and the remote control should be kept free of obstacles.
The remote control has a range of 10 meters.
Remote Control Battery
1.
The battery positive (+) should face as shown below.
2.
The arrow indicates the plastic lock.
Button
Function
ON/OFF
Press to turn unit on, press again to turn off
AUTO
Activate AUTO mode. Use ± to select the preset program
from AUTM-AUTS
PRG
Active Show mode. Use ± to select the preset program
from St01-20
SOUND
Turn Sound Control On/OFF for AUTO and PRG. When ON,
press ± to adjust the sensitivity from S001 to S100 *
SPEED
Activates speed setting when AUTO and PRG mode is ON. Use
± to adjust the speed from SP01 to SP99 *
STROBE
Activates derby light strobe. Use ± to adjust the speed from
FS00 to FS99 *
+
Press to increase the current value. Press - to decrease.
DIMMING
Dimmer can be used for derby light only
-
Press to decrease the current value to a minimum value of 0.
Press + to increase.
W, R, G, B
Select color for dimmer mode (White, Red, Green, Blue).
Note: A and UV are not available
1 to 9
Select preset color
Notes
* Each press of ± increases/decreases by 1, but if held down,
the values change faster.
48
49
Quick Start Guide
LED DERBY DSL1
Содержание EUROLIGHT LED DSL1
Страница 1: ...Quick Start Guide EUROLIGHT LED DSL1 Dual Mode Derby Effect and Strobe Light V 1 0 ...
Страница 42: ...82 83 Quick Start Guide LED DERBY DSL1 ...
Страница 43: ...We Hear You ...