manualshive.com logo in svg

Beckman Coulter Microfuge 20 Series, Инструкция по эксплуатации

Поделиться
Скачать
Beckman Coulter Microfuge 20 Series Скачать руководство пользователя страница 65

B30162AA

A-3

Installation

Electrical Requirements  

A

Electrical Requirements

See the 

Microfuge 20 Nonrefrigerated Model Specifications

 or 

Microfuge 20R Refrigerated Model 

Specifications

 in 

CHAPTER 1

 for centrifuge electrical requirements.

Make sure the voltage and frequency imprinted on the name rating plate affixed to the back of the 
centrifuge agree with the line voltage and frequency of the outlet used. Refrigeration does not 
function properly if the frequency [Hz] does not match the name rating plate. Plug in both ends of 
the centrifuge power cord. If there is any question about voltage, have a qualified service person 
measure it under load while the drive is operating.

A 1.8-m (6-ft) power cord with grounded plug is supplied with the centrifuge. Make sure that the 
matching wall outlet is located near the centrifuge and is easily accessible.

NOTE

The power plug serves as the Disconnecting Device and must remain easily accessible.

Figure A.1  

Dimensions of the Non-Refrigerated Centrifuge

Содержание Microfuge 20 Series











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды