manualshive.com logo in svg

Beckman Coulter Microfuge 20 Series, Инструкция по эксплуатации

Поделиться
Скачать
Beckman Coulter Microfuge 20 Series Скачать руководство пользователя страница 18

B30162AA

xviii

Introduction

Symbols and Labels  

 •

the device is not to be disposed of via the municipal waste collection system of any member 
state of the European Union.

It is very important that customers understand and follow all laws regarding the proper 
decontamination and safe disposal of electrical equipment. For Beckman Coulter products bearing 
this label, please contact your dealer or local Beckman Coulter office for details on the take-back 
program that will facilitate the proper collection, treatment, recovery, recycling and safe disposal 
of the device.

Risk of Fire Warning

Before replacing fuses, shut off power and disconnect the power cord. Failure to do so can cause 
electric shock and/or equipment damage. Replace fuses only with approved type and rating 
replacement fuse.

Electric Shock Warning

 Operation, replacement or servicing of any components where contact with electronic 
components could occur can result in electric shock, and should only be performed by your 
Beckman Coulter representative.

Rotor Rotation

This label indicates the direction of the rotor rotation.

Содержание Microfuge 20 Series











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды