manualshive.com logo in svg

Beckman Coulter Microfuge 20 Series, Инструкция по эксплуатации

Поделиться
Скачать
Beckman Coulter Microfuge 20 Series Скачать руководство пользователя страница 53

B30162AA

3-5

Troubleshooting

Other Possible Problems  

3

Other Possible Problems

Possible malfunctions that may not be indicated by diagnostic messages are described in 

Table 3.2

, 

along with probable causes and corrective actions required. Possible causes for each problem are 
listed in the probable order of occurrence. Perform the recommended corrective action in 
sequence, as listed. If you are unable to correct the problem, call Beckman Coulter Field Service.

Table 3.2  

Troubleshooting Chart

Problem

Possible Reason

Recommended Action

Display is blank

1.

No power to the mains supply.

2.

Power cord is not plugged in.

3.

Mains power is switched off.

4.

Door is not closed correctly.

1.

Check the fuse in the mains supply.

2.

Plug in the power cord correctly.

3.

Switch the mains power on.

4.

Close the door.

Centrifuge cannot be 
started; The 
displayed set speed 
value cannot be 
changed.

1.

Several .

2.

The door lock is not closed 
correctly.

1.

Cycle power. If the error persists, contact Beckman 
Coulter Field Service.

2.

Open and close the door. If the error persists, 
contact Beckman Coulter Field Service.

Centrifuge 
decelerates during 
operation and 
displays an error from 
1 to 18 after powering 
on.

Several 

Cycle power. If the error occurs again, contact 
Beckman Coulter Field Service.

Centrifuge 
decelerates during 
operation and 
displays error 19 after 
powering on.

Several .

Quit by pressing the door key.

Temperature value 
cannot be reached 
(applies to 20R 
Refrigerated 
centrifuges only).

Dirty condenser.

Contact Beckman Coulter Field Service.

Содержание Microfuge 20 Series











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды