manualshive.com logo in svg

Beckman Coulter Microfuge 20 Series, Инструкция по эксплуатации

Поделиться
Скачать
Beckman Coulter Microfuge 20 Series Скачать руководство пользователя страница 44

B30162AA

2-14

Operation

Unloading  

Unloading

NOTE

When you remove the rotor, make sure that the tapered sleeve from the centrifuge drive shaft 

does not come out with the rotor. If the tapered sleeve is inside the rotor drive hole, call 
Beckman Coulter Field Service at 1-800-742-2345 (U.S.A or Canada); outside the U.S. contact your local 
Beckman Coulter office or visit us at 

www.beckmancoulter.com

).

After completing a run, unload the rotor following the instructions in the applicable rotor manual. 

CAUTION

If disassembly reveals evidence of leakage, you should assume that some fluid 
escaped the rotor. Apply appropriate decontamination procedures to the 
centrifuge and accessories.

Summary of Run Procedures

For runs at other than room temperature, refrigerate or warm the rotor beforehand for fast equilibrium. 
For low-temperature runs, precool the centrifuge by running a 30-minute cycle (with a precooled rotor 
installed) at the required temperature with the speed set at 2000 rpm.

1

Press the POWER switch to on (

I

). 

a.

Open the centrifuge door (press the 

OPEN

 key and lift the door up).

2

Make sure that the tapered sleeve is in place at the base of the centrifuge drive shaft before 
installing the rotor. 

 •

The rotor does not operate properly if the sleeve is missing.

3

Install the rotor according to the instructions in the applicable rotor manual. 

CAUTION

Always run the rotor with a balanced load.

4

Close the centrifuge door and push firmly down on both sides of the door front until the 
clicking (latching) sound stops.

Содержание Microfuge 20 Series











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды