manualshive.com logo in svg

Beckman Coulter Microfuge 20 Series, Инструкция по эксплуатации

Поделиться
Скачать
Beckman Coulter Microfuge 20 Series Скачать руководство пользователя страница 64

B30162AA

A-2

Installation

Installing the Instrument  

 •

Do not subject the centrifuge to thermal stress. For example, do not position the centrifuge 
near a source of heat.

 •

Do not position the centrifuge where it receives direct sunlight (UV radiation).

 •

The table or bench that the centrifuge is installed on must be stable and have a solid, flat 
surface.

 •

After moving the centrifuge from cold to warmer rooms, condensation may collect inside the 
centrifuge. It’s important to allow at least 24 hours for drying before using the centrifuge again.

To install the centrifuge

1

The centrifuge ships in a cardboard box. For easy access, remove the top of the box, the foam 
insert on top of the centrifuge, and then the upper part (sides) of the box and set them aside. 

a.

Then, 

with the help of another person

, move the centrifuge to its final position.

 •

(Note the warning above regarding centrifuge weight.)

2

Position the centrifuge on a level surface, such as a sturdy table or laboratory bench that is able 
to support the weight of the centrifuge and resist vibration. 

 •

Refer to 

Microfuge 20 Nonrefrigerated Model Specifications

 or 

Microfuge 20R Refrigerated Model 

Specifications

 in 

CHAPTER 1

 for weight.

a.

Make sure that the centrifuge front feet are fully supported on the table.

b.

Locate the centrifuge in an area with sufficient ventilation to allow for heat dissipation. 

c.

Check that there are 30 cm (12 in.) clearances at the sides of the centrifuge to ensure 
sufficient air circulation. 

Dimensions are shown in 

Figure A.1

 or 

Figure A.2

.

The centrifuge must have adequate air ventilation to ensure compliance to local 
requirements for vapors produced during operation.

For ambient temperature ranges see 

Microfuge 20R Refrigerated Model Specifications

 and 

Microfuge 20 Nonrefrigerated Model Specifications

.

NOTE

During transport between areas with varying temperatures, condensation may occur inside 

the centrifuge. Allow sufficient drying time before running the centrifuge.

Содержание Microfuge 20 Series











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды