Beckhoff EP4174-0002 Скачать руководство пользователя страница 28

Страница: 28 / 63

Mounting and connection

EP4174-0002

Version: 1.1.0

3.2.6.2

Analog current outputs (M12)

Analog outputs, 0 to 20 mA or 4 to 20 mA

The actuator is connected via and output -. The actuator can optionally be operated/supplied with
24 V

Fig. 24: Connecting the analog current outputs (M12)

LED indicators - meanings

There is a green

Run

LED and a red

Error

LED for each channel. The green

Run

LED is lit when data are

transferred to the D/A converter. The red

Error

LED indicates that there is an error (open circuit, measured

value outside the range).
Correct function is indicated if the green

Run

LED is on and the red

Error

is off.

Fig. 25: Status and diagnostic LED at the M12 connector

3.3

UL Requirements

The installation of the EtherCAT Box Modules certified by UL has to meet the following requirements.

Supply voltage

CAUTION

CAUTION!

This UL requirements are valid for all supply voltages of all marked EtherCAT Box Modules!
For the compliance of the UL requirements the EtherCAT Box Modules should only be supplied

• by a 24 V

supply voltage, supplied by an isolating source and protected by means of a fuse (in accor-

dance with UL248), rated maximum 4 Amp, or

• by a 24 V

power source, that has to satisfy

NEC class 2

power supply shall not be connected in series or parallel with another (class 2) power

source!

CAUTION

CAUTION!

To meet the UL requirements, the EtherCAT Box Modules must not be connected to unlimited power
sources!

Содержание EP4174-0002
































































Результаты поиска

Содержание EP4174-0002

Отзывы:

Похожие инструкции для EP4174-0002

Бренды по названию

Популярные бренды

Beckhoff EP4174-0002, Документация

Результаты поиска

Содержание EP4174-0002

Отзывы:

Похожие инструкции для EP4174-0002

Бренды по названию

Популярные бренды