Beckhoff EP4174-0002 Скачать руководство пользователя страница 20

Страница: 20 / 63

Mounting and connection

EP4174-0002

Version: 1.1.0

3.2.2

EtherCAT - Fieldbus LEDs

Fig. 16: EtherCAT-LEDs

LED display

LED

Display

Meaning

IN L/A

off

no connection to the preceding EtherCAT module

Lit

LINK: connection to the preceding EtherCAT module

flashing

ACT: Communication with the preceding EtherCAT module

OUT L/A

off

no connection to the following EtherCAT module

Lit

LINK: connection to the following EtherCAT module

flashing

ACT: Communication with the following EtherCAT module

Run

off

Status of the EtherCAT module is Init

flashes quickly

Status of the EtherCAT module is pre-operational

flashes slowly

Status of the EtherCAT module is safe-operational

Lit

Status of the EtherCAT module is operational

EtherCAT statuses

The various statuses in which an EtherCAT module may be found are described in the Basic Sys-
tem Documentation for EtherCAT, which is available for download from our website (

www.beck-

hoff.com

) under Downloads.

Содержание EP4174-0002
































































Результаты поиска

Содержание EP4174-0002

Отзывы:

Похожие инструкции для EP4174-0002

Бренды по названию

Популярные бренды

Beckhoff EP4174-0002, Документация

Результаты поиска

Содержание EP4174-0002

Отзывы:

Похожие инструкции для EP4174-0002

Бренды по названию

Популярные бренды