Beckhoff AMI8100 Скачать руководство пользователя страница 39

Страница: 39 / 61

Technical description

Version: 1.0

───

AMI8100

7.6

Display

The LEDs of the AMI812x compact integrated servo drive provide
you with information about the operating state. There are different
light sequences for each operating state.

7.6.1

Status LEDs

This section provides information about the meaning of the different
status LEDs on the AMI812x compact integrated servo drive.

7.6.1.1

Supply voltage

7.6.1.1

Us out 1 and 2 = status display of the supply voltage

LED

Status

lit

Supply voltage present at out-
puts 1 and 2

Off

No supply voltage present at out-
puts 1 and 2

Us in 1 and 2 = status display of the supply voltage

LED

Status

lit

Supply voltage present at inputs
1 and 2

Off

No supply voltage present at in-
puts 1 and 2

7.6.1.2

Motor voltage

7.6.1.2

Up = status display of the power supply of the servo drive

LED

Status

lit

Peripheral voltage present

Off

No peripheral voltage present

Содержание AMI8100






























































Результаты поиска

Содержание AMI8100

Отзывы:

Похожие инструкции для AMI8100

Бренды по названию

Популярные бренды

Beckhoff AMI8100, Руководство по эксплуатации

Результаты поиска

Содержание AMI8100

Отзывы:

Похожие инструкции для AMI8100

Бренды по названию

Популярные бренды