Beckhoff AMI8100 Скачать руководство пользователя страница 55

Страница: 55 / 61

Decommissioning

Version: 1.0

───

AMI8100

Disassembly may only be carried out by qualified and trained per-
sonnel.

Read the chapter Documentation notes.

When disposing of electronic waste, make sure that you dispose of
it in accordance with the regulations applicable in your country.
Read and follow the instructions for proper disposal.

13.1

Disassembly

WARNING

Risk of injury from leaking oil

Prevent oil from leaking. Let it cool down before starting work.
Soak up any leaked oil with approved binding agents. Mark the
danger spot.

Leaking oil can cause slips and falls, resulting in serious or fatal
injury. Hot oil can cause severe burns.

Do not remove components from the products

Only Beckhoff Automation GmbH & Co. KG is permitted to remove
components.
Contact Beckhoff Service if you have any questions.

Removal of the servo drive from the machine

• Remove cables and electrical connections

• Cool and drain liquids, then remove

• Remove supply lines and water hoses

• Loosen and remove the servo drive fixing screws

• Transport the servo drive to the workplace or put it into storage

Содержание AMI8100






























































Результаты поиска

Содержание AMI8100

Отзывы:

Похожие инструкции для AMI8100

Бренды по названию

Популярные бренды

Beckhoff AMI8100, Руководство по эксплуатации

Результаты поиска

Содержание AMI8100

Отзывы:

Похожие инструкции для AMI8100

Бренды по названию

Популярные бренды