manualshive.com logo in svg

Bay Networks Remote Annex 2000, Руководство по установке оборудования

Поделиться
Скачать
Bay Networks Remote Annex 2000 Скачать руководство пользователя страница 31

1-11

Remote Annex 2000 Hardware Installation Guide

Chapter 1    Introduction

Console Port
(Port 1)

The console port (Port 1) provides access to the ROM Monitor
commands when the Remote Annex 2000 is in test mode.

RJ45 Port
Connectors

The RJ45 Port Connectors connect from 1 to 16 asynchronous serial
devices to the Remote Annex 2000.

Network Interface
Connectors

The Remote Annex 2000 has the following network interface ports for
connecting to a LAN:

❑

10Base2 Ethernet port with a BNC connector (optional).

❑

10Base5 Ethernet transceiver port with a DB15 connector.

❑

10BaseT Ethernet port with an RJ45 connector (optional).

The DB15 Ethernet 10Base5 transceiver port is present on the rear
panel even when another network interface port is present. The BNC
10Base2 and RJ45 10BaseT connectors are present only if ordered with
the unit. The Remote Annex 2000 automatically determines which
interface to use.

Connect only one interface at a time.

The Remote Annex 2000 must be reset when changing network
interface connections.

Power Switch

The Power Switch disconnects AC power without disconnecting the
Remote Annex 2000 from the power source.

Содержание Remote Annex 2000









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды