Bay Networks Remote Annex 2000 Скачать руководство пользователя страница 101

Страница: 101 / 136

4-9

Remote Annex 2000 Hardware Installation Guide

Chapter 4 Troubleshooting Procedures

Test Mode Error Sequences

describes the state of the LEDs if errors occur at different

stages of the start-up process. For example, if the Remote Annex 2000
fails while testing the hardware (state T2), the error condition is
hardware failure TE2. A description of each error condition follows

Table 4-4

Table 4-4. Test Mode Error LED States

Key:

●

On continuously.

Off.

■

Flashing irregularly.

◆

Flashing regularly (about 1Hz).

Activity

Power
green

Unit
green

Net
green

Attn
amber

Load
green

Active
green

TE2:
Hardware failure

●

◆

TE3: Network test
failure

●

◆

■

TE4: Network test
aborted or net
command failed

●

◆

■

TE7: Booted
wrong image

●

◆

Содержание Remote Annex 2000









































































































































Результаты поиска

Содержание Remote Annex 2000

Отзывы:

Бренды по названию

Популярные бренды

Bay Networks Remote Annex 2000, Руководство по установке оборудования

Результаты поиска

Содержание Remote Annex 2000

Отзывы:

Бренды по названию

Популярные бренды