manualshive.com logo in svg

Bay Networks Remote Annex 2000, Руководство по установке оборудования

Поделиться
Скачать
Bay Networks Remote Annex 2000 Скачать руководство пользователя страница 103

4-11

Remote Annex 2000 Hardware Installation Guide

Chapter 4    Troubleshooting Procedures

If the Remote Annex 2000 still is not booted, you must pinpoint the
problem. The boot error report can help in this process.

The Remote Annex 2000 generates and displays a boot error
report only if it has opened the boot file and an error occurs
during the boot process.

Generally, two problems cause boot failures: the Remote Annex 2000
is not configured properly, or the load server host is not responding.
The Remote Annex 2000 requests a boot either from a pre-defined
load host, or by broadcasting its boot request. When a host responds,
the Remote Annex 2000 loads its operational code.

The Remote Annex 2000 requires setting certain configuration
parameters. Enter these parameters with ROM Monitor commands
for the initial boot sequence. Chapter 3 describes these commands in
detail.

If the problem is a non-responsive host, the boot error report displays
that information under the Rsp T/Os field. This field indicates that the
Remote Annex 2000 timed out while waiting for a response to its boot
request; if this field is empty, check the Remote Annex 2000’s
configuration parameters.

Содержание Remote Annex 2000









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды