manualshive.com logo in svg

Bay Networks Remote Annex 2000, Руководство по установке оборудования

Поделиться
Скачать
Bay Networks Remote Annex 2000 Скачать руководство пользователя страница 113

4-21

Remote Annex 2000 Hardware Installation Guide

Chapter 4    Troubleshooting Procedures

The Remote Annex 2000 sends a dump file to a preferred load dump
host. If you do not define this host by specifying an address, the
Remote Annex 2000 broadcasts a request and dumps to the first host
that responds.

The Remote Annex sends a dump to the /usr/spool/erpcd/bfs
directory on the dump host. The /usr/spool/erpcd/bfs directory is a
default pathname and can be changed. The receiving Remote Annex
assigns a unique file name for each device that it receives a dump
from but not for each crash dump.

Rename any crash dumps that you want to save. The Remote
Annex 2000 overwrites crash dumps.

The assigned name depends on the number of characters per file name
that the dump host supports. For hosts supporting file names longer
than 14 characters (e.g., BSD hosts), dump files are named dump.addr.
The file extension addr is the Remote Annex 2000’s IP address.

For hosts that limit file names to 14 characters (e.g., System V
 hosts), a dump creates two additional directories under

/usr/spool/erpcd/bfs

. The name of the first directory is dump; the

second directory uses the Remote Annex 2000’s IP network address
as its name. The dump file uses the Remote Annex 2000’s IP host
address as its name.

The tftp dump names are user-defined. If a name is not
specified, the Remote Annex uses the bfs convention.

Содержание Remote Annex 2000









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды