Baxi Nuvola 3 Comfort Скачать руководство пользователя страница 20

Страница: 20 / 40

C607215 - GB

INSTRUCTIONS FOR FITTERS

16.5 SEPARATE VERTICAL FLUE INSTALLATION OPTIONS

L max = 15 m

911231_4701

17. ELECTRICAL CONNECTIONS

This machine is only electrically safe if it is correctly connected to an efficient earth system in compliance with current safety regula-

tions.

Connect the boiler to a 230V single-phase earthed power supply using the supplied three-pin cable, observing correct LIVE-NEUTRAL

polarity.

Use a double-pole switch with a contact separation of at least 3 mm.

When replacing the power supply cable, fit a harmonised HAR H05 VV-F’ 3x0.75mm2 cable with a maximum diameter of 8 mm.

…Access to the power supply terminal block

• disconnect the boiler from the mains power supply using the two-pole switch;

• remove the two screws fixing the control panel to the boiler;

• rotate the control panel;

• remove the cover and access the wiring area (figure 11).

The 2A fast-blowing fuse is incorporated in the power supply terminal block (to check and/or replace the fuse, pull out the black fuse car-

rier).

(L) =

Live

(brown)

(N) =

Neutral

(blue)

Earth

(yellow-green)

(1) (2) =

Contact for ambient thermostat

IMPORTANT

respect polarity

(LIVE) -

(NEUTRAL)

Figure 11

0609_0602 / CG_1853

WARNING:

If the appliance is directly connected to an underfloor system, install a safety thermostat to prevent the latter from

overheating

Содержание Nuvola 3 Comfort









































Результаты поиска

Содержание Nuvola 3 Comfort

Отзывы:

Бренды по названию

Популярные бренды

Baxi Nuvola 3 Comfort, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание Nuvola 3 Comfort

Отзывы:

Бренды по названию

Популярные бренды