Baxi Fires Division 941 Скачать руководство пользователя

Страница: 4 / 40

Page 4

INSTALLER GUIDE

Baxi Heating U.K. Limited 2007.

CONTENTS

Section

Heading

Page

1. SAFETY

2. APPLIANCE DATA

3. GENERAL INSTALLATION REQUIREMENTS

4. PACK CONTENTS

5. FIREPLACE CHECK

6. IGNITION CHECK

7. GAS SUPPLY CONNECTION

8. PREPARING APPLIANCE FOR INSTALLATION

9. HOTBOX INSTALLATION

9.1 Method 1 - Front fixing to fireplace surround.

9.2 Method 2 - Cable retention and floor fixing.

9.3 Sealing floor front

10. BURNER & SUPPLY PIPE INSTALLATION

10.1 Burner and supply pipe installation.

10.2 Preliminary burner checks.

10.3 Inlet pressure check.

11. CERAMIC WALLS INSTALLATION

12. FITTING THE FASCIA

13. FITTING THE CERAMIC FUEL EFFECT

14. FITTING THE FIREFRONT

15. FULL OPERATING CHECKS

15.1 Check the control settings.

15.2 Check for spillage.

15.3 Flame supervision and spillage monitoring system.

16. FINAL REVIEW

17. SERVICING & PARTS REPLACEMENT

17.1 Checking the aeration setting of the burner.

17.2 To remove the Westminster and Bolero fascia.

17.3 To remove the Victorian fascia.

17.4 To remove the Anthem, Blenheim, Camden, Minima and Sonnet fascia.

17.5 To remove the complete burner unit.

17.6 To remove the pilot unit.

17.7 To remove the gas valve.

17.8 To remove the piezo generator.

17.9 To grease the control tap.

17.10 To replace the burner.

17.11 To remove the main burner injector.

17.12 To remove the appliance from the fireplace.

Содержание 941









































Результаты поиска

Содержание 941

Отзывы:

Похожие инструкции для 941

Бренды по названию

Популярные бренды

Baxi Fires Division 941, Руководство по установке

Результаты поиска

Содержание 941

Отзывы:

Похожие инструкции для 941

Бренды по названию

Популярные бренды