Baxi Fires Division 941 Скачать руководство пользователя страница 39

Страница: 39 / 40

17.7 To remove the gas valve.

(See figure 40).

Remove the burner unit (See

section 17.5).

If lying the burner on its back,

ensure that the work surface is
suitably protected This will avoid
damage to the work surface.Turn the
burner unit upside down. Detach the
thermocouple from the tap

Detach the pilot pipe from the tap.

Detach the inlet pipe.

5. Detach the injector pipe

Detach the electrode lead from the

base of the electrode

Remove the control knob by pulling forward.

Remove the thermocouple by unscrewing the thermocouple nut at the gas valve.

Remove the hexagonal nut securing the gas valve to the mounting bracket.

10.

Remove the gas valve

11.

Refit in the reverse order.

17.8 To remove the piezo generator.

Remove the gas tap as section 17.7.

Make sure that the tap is in the off position.

Remove the circlip holding the piezo unit to the tap. Remove the piezo unit.

Replace in the reverse order.

17.9 To grease the control tap.

Detach the tap and remove the piezo generator as section 17.8 making sure that the

tap is in the off position.

Remove the two screws from the head of the tap. Remove the niting head and

spindle complete with collar and spring.

Note the position of the slot in the plug-mark its position on the tap body.

Remove the plug rotating slightly while pulling.

Clean and grease the plug lightly with suitable grease. Do not apply excessive

grease. Particularly, make sure that the gas ports in the tap are not restricted by grease.

Push the plug into the tap body and position the slot in line with the mark previously

made on the tap body.

Reassemble the niting head and spindle complete with collar and spring making sure

that the components are correctly engaged. Check the operation of the tap.

Refit the piezo generator.

Page 39

INSTALLER GUIDE

Baxi Heating U.K. Limited 2007.

Figure 40. Gas valve (Viewed from rear with
burner turned over)

Содержание 941









































Результаты поиска

Содержание 941

Отзывы:

Похожие инструкции для 941

Бренды по названию

Популярные бренды

Baxi Fires Division 941, Руководство по установке

Результаты поиска

Содержание 941

Отзывы:

Похожие инструкции для 941

Бренды по названию

Популярные бренды