Heat & Glo RUTH42-B страница 1 Скачать руководство пользователя

Страница: 1 / 44

Heat & Glo • Rutherford 42-B Installation Manual • 4059-712 • Rev O • 09/28/15

WOODBURNING FIREPLACE

Fire Risk.

WARNING

For use with solid wood fuel only.

Other fuels may overfire and generate

poisonous gases (i.e. carbon monoxide).

Model(s):

Installation Manual

Installation and Fireplace Setup

WARNING

HOT SURFACES

Glass and other surfaces are hot during

operation AND cool down.

Hot glass will cause burns.

•

DO NOT

touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as

fireplace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable

materials.

• Keep clothing, furniture, draperies and other flammable

materials away.

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

RUTH42-B

NOTICE: DO NOT

discard this manual!

•

DO NOT

store or use gasoline or other flam

mable vapors and liquids in the vicinity of this

or any other appliance.

•

DO NOT

overfire. Overfiring will void your

warranty.

• Comply with all minimum clearances to com

bustibles as specified. Failure to comply may

cause house fire.

WARNING: If the information in these

instructions is not followed exactly, a fire

or explosion may result causing property

damage, personal injury, or death.

Installation and service of this

appliance should be performed by

qualified personnel. Hearth & Home

Technologies recommends HHT

Factory Trained or NFI certified

professionals.

Содержание RUTH42-B













































Результаты поиска

Содержание RUTH42-B

Отзывы:

Похожие инструкции для RUTH42-B

Бренды по названию

Популярные бренды

Heat & Glo RUTH42-B, Руководство по установке

Результаты поиска

Содержание RUTH42-B

Отзывы:

Похожие инструкции для RUTH42-B

Бренды по названию

Популярные бренды