Heat & Glo RUTH42-B страница 25 Скачать руководство пользователя

Страница: 25 / 44

Heat & Glo • Rutherford 42-B Installation Manual • 4059-712 • Rev O • 09/28/15

Shrouds

3 in. (76 mm) tall legs

Ø 17 1/2 in. (444.5 mm) Round Hole to fit over cap

Length x Width to fit inside shroud

Figure 6.1 Radiation Shield

WARNING! Risk of Fire!

Shrouds must be constructed

as specified. Improper construction may overheat

chase top.

NOTICE: Some regional codes require an agency-Listed

shroud. Consult your local building officials.

Shrouds may be field constructed where permitted by

regional building codes.

The shrouds must be constructed from minimum .018

in. (26 ga) thick aluminized steel.
Some shrouds require a radiation shield. Use where

specified.

A. Radiation Shield

Radiation shield must be constructed of minimum 26 ga

thick sheet metal.

B. Field Constructed Shrouds

The following field constructed shroud designs have

been tested for HHT fireplace systems and termination

caps.

3 in (76 mm)

minimum

Min.

Base Dim.

Min.

Base Dim.

Min.

Top Dim.

Min.

Top Dim.

Min. Opening

Width

Min. Opening

Width

Radiation

Shield

14 1/2 in. (368 mm)

maximum height

Figure 6.2 Open Top Shroud Dimensions

TR11/11T

TR11/11T TV

Min. Base Dims.

32 x 32

26 x 26

813 x 813

660 x 660

Radiation Shield

Required

Radiation

Shield Not

Required

Min. Top Dims.

29 x 29

23 x 23

737 x 737

584 x 584

Min. Opening Width

26 x 26

20 x 20

660 x 660

508 x 508

1. Open Top Shroud

TR11/TR11T TV (top vent) caps do not require radiation

shield.

TR11/TR11T caps require radiation shield unless in

stalled partially above the shroud. The TR cap must be

raised to the minimum dimensions (or greater) above the

shroud. Refer to Figure 6.3.

6" Min.

Above the

Shroud.

Storm

Collar

Shroud

Leg

(SHROUD)

(TR Series)

Flue

Shroud

Leg

3 in (76 mm)

air space from

bottom of shroud

to top of chase.

Maximum Height

14 1/2 in. (368 mm)

Chase Top

Figure 6.3 Shroud & TR Series cap with no Radiation Shield

Содержание RUTH42-B













































Результаты поиска

Содержание RUTH42-B

Отзывы:

Похожие инструкции для RUTH42-B

Бренды по названию

Популярные бренды

Heat & Glo RUTH42-B, Руководство по установке

Результаты поиска

Содержание RUTH42-B

Отзывы:

Похожие инструкции для RUTH42-B

Бренды по названию

Популярные бренды