Heat & Glo RUTH42-B страница 30 Скачать руководство пользователя

Страница: 30 / 44

Heat & Glo • Rutherford 42-B Installation Manual • 4059-712 • Rev O • 09/28/15

* 2 in. (51 mm)

Continuous,

non-combustible sealant

Tile, stone or other

non-combustible material

Floor constructed of wood or

other combustible material

1 in. Micore and 1/2

in. Durock or

equivalent insulation

(see Table)

Fireplace

Protective

Metal Hearth

Strip

Durock

Note:

The bottom of the fireplace opening is 3-3/4 in. (95.3mm) above

the bottom of the fireplace. Finished hearth must NOT extend above this

level.

Figure 7.5 Hearth Extension Construction

Floor

Noncombustible

Framing Material

Noncombustible

Finishing Material

Protective Metal

Hearth Strips

1 in. Micore and

1/2 in. Durock

or equivalent

insulation

20 in. Min.

Hearth Extension

Note: The bottom of the fireplace

opening is 3-3/4 in. (95.3 mm)

above the bottom of the

fireplace. Finished hearth must

NOT extend above this level.

Noncombustible

Framing Material

HX4 or

equivalent

Figure 7.7 Raised Platform Hearth Extension-Framing

Non-combustible

Finishing Materials

Figure 7.8 Raised Platform Hearth Extension-Finishing

Figure 7.6 Raised Platform Hearth Extension Detail

1. Fireplace Installed Flush on the Floor and

Hearth Extension Raised to Bottom of Firebox

Opening

Non-combustible flooring a minimum of 20 in. (508

mm) in front of and 12 in. (305 mm) to each side of the

fuel opening is required.
The hearth framing must be constructed of non-com

bustible materials (such as metal framing or equivalent

material) and placed on HX3(s) or HX4(s) and 1/2 in.

Durock, or equivalent material. Refer to Figure 7.5.

When creating the platform, allow for the thickness

of the non-combustible finishing materials

Seal gaps between the hearth extension and the front

of the fireplace with a bead of non-combustible sealant

or grout.

Содержание RUTH42-B













































Результаты поиска

Содержание RUTH42-B

Отзывы:

Похожие инструкции для RUTH42-B

Бренды по названию

Популярные бренды

Heat & Glo RUTH42-B, Руководство по установке

Результаты поиска

Содержание RUTH42-B

Отзывы:

Похожие инструкции для RUTH42-B

Бренды по названию

Популярные бренды