Baur PD-TaD 80 Скачать руководство пользователя страница 60

Страница: 60 / 74

Maintenance

PD-TaD 80

60 / 74

822-188-3

14.1 Special maintenance instructions

NOTICE

Damage to device due to improper handling

The user is liable for damages caused due to improper maintenance or care.



Never take apart the device. This can lead to device damages. Inside the device

there are no components that could be serviced or repaired by the user.



Maintenance tasks must be carried out only by personnel trained and authorised

by BAUR

NOTICE

The housing of the HV coupling unit is locked gas-proof and may not be opened.



Do not dismantle the HV coupling unit.



Do not screw any components onto the HV coupling unit. Opening the housing

can damage the device.

14.2 Cleaning the PD-TaD 80 and system components

NOTICE

Damage to the device may be caused by using the wrong cleaning agents



Do not use any abrasive, corrosive cleaning agents or strong solvents.



Ensure material compatibility.



Do not clean the product with acetone or thinner.



Never clean electrical devices with water.



Mild detergent for cleaning the surfaces of the device



Lint-free cleaning cloth



Keep the connectors and the surface of the HV coupling unit (PD-TaD 80) clean and dry.

Dirt and moisture will have a negative effect on the measurement results.



Clean the device surfaces with mild detergent and a lint-free cloth on a regular basis.



Clean the connection cables and terminations with mild detergent and a lint-free cloth.

AINTENANCE

Содержание PD-TaD 80











































































Результаты поиска

Содержание PD-TaD 80

Отзывы:

Baur PD-TaD 80, Руководство пользователя, Страница: 60 / 74

Результаты поиска

Содержание PD-TaD 80

Отзывы: