Baur PD-TaD 80 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 74

Baur PD-TaD 80 Скачать руководство пользователя страница 54

VLF cable testing with parallel partial discharge testing

PD-TaD 80

54 / 74

822-188-3

Whereas VLF cable testing shows whether a cable can withstand a load over a specified test
duration, PD testing identifies and locates the PD activities of the cable insulation.

The simultaneous performance of VLF cable testing and PD testing can reduce the test time
for cables that are in good condition.

1. Connect the test object for PD testing.

Further information: Chapter

Connecting the system for PD measurement

(on page 35)

2. Calibrate the PD test circuit.

3. Start VLF cable testing.

4. Configure and start PD testing in the BAUR software.

5. Monitor the trend of the PD measurement results during testing.



Information on calibrating the PD test circuit as well as performing

PD testing and VLF cable testing is given in the user manual for the
BAUR software 4.



Information on operating the cable test van or VLF HV generator is

given in the user manual for the cable test van or the respective
VLF HV generator.

10

VLF

CABLE TESTING WITH PARALLEL PARTIAL

DISCHARGE TESTING

«
...
52
53
54
55
56
...
»

Содержание PD-TaD 80











































































Отзывы:

Нет отзывов