manualshive.com logo in svg

Baumer O200, Инструкция по эксплуатации

Поделиться
Скачать
Baumer O200 Скачать руководство пользователя страница 18

 

en_BA_O200_IO-Link_V1.docx 

18/34 

Baumer Electric AG 

15.08.2018/ 

 

Frauenfeld, Switzerland

 

4.3.4 

Counter / SSC4 

For each individual SSC a switching counter is implemented, which can be used as diagnosis data or also as 
measurement value. The number of counts of each channel can also be mapped to the measurement data 
channel MDC by adjusting the MDC source (See section 4.2.3). 
Trigger of counter is on positive slope of related SSC. 
 
By configuring SSC4, it is also possible to set up a binary signal related to the number of switchcounts of 
SSC1. An auto-reset and timefilters are included, to be able to create a full-featured counter being able to 
count lot sizes without any need to code software on the PLC.  
 
As all SSCs, SSC4 can also be mapped to the digital output giving the possibility to create a stand-alone lot-
size counter. 
 
In section 3.1, the signal path is decribed more detailed, to illustrate how the counter module is implemented. 
In section 4.3.4.2 the behavior depending on the configuration is explained. 
 

4.3.4.1 

SSC4 Configuration 

In general the SSC4 offers the same features as the SSC1 and SSC2 based on distance (See 4.3.2), 
including also timefilters. 
Exceptions: 

- 

No hysteresis settings as there are only incremental counts. 

- 

Additional parameters to adjust like 

SSC4 Source

 and 

SSC4 Auto-Reset. 

 
Parameter name

 

Short Description

 

Rights

 

Unit / Allowed values

 

SSC4 Setpoints.SP1   

Set the number of counts at which the 
SSC is set to active (or inactive if 
inverted) 

rw 

Counts / 0 to 32759 

SSC4 Setpoints.SP2 

Set the number of counts at at which the 
SSC is set to inactive (or active if 
inverted) 

- 

only active if SSC is set to 
window mode 

rw 

Counts / 0 to 32759 

 

 

Parameter name 

Short Description 

Rights 

Unit / Allowed values 

SSC4 Config.Logic 

Changes the Logic from NO to NC   rw 

- 

Normal 

- 

Inverted 

SSC4 Config.Mode 

Selection of the switching mode 

rw 

- 

Single Point  

- 

Window 

SSC4 Config.Source 

Selection of source for counter 
function 

rw 

- 

SSC1 Switch Counter 

SSC4 Config.Auto Reset 

Autoreset of switch counter if given 
switch counts are reached. 
If autoreset is switched from 
disabled to enabled, the selected 
switch counter-source is 
automatically being reset to zero. 

rw 

- 

Enabled 

- 

Disabled 

 
 
 
 

Содержание O200



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды