manualshive.com logo in svg

Baumer O200, Инструкция по эксплуатации

Поделиться
Скачать
Baumer O200 Скачать руководство пользователя страница 32

 

en_BA_O200_IO-Link_V1.docx 

32/34 

Baumer Electric AG 

15.08.2018/ 

 

Frauenfeld, Switzerland

 

5.3.2 

Dynamic in Window Mode (Only O200.G) 

If the selected SSC is configured to Window mode (Section 4.3.2.1) during the dynamic teach-in the 
minimum and maximum values are evaluated. Setpoint SP1 is set to Min, SP2 is set to Max. 
 

 

Figure 29: Dynamic Window Teach, switching behavior 

 
 
 

6 

Diagnosis 

In addition to solving the primary application, the simple evaluation of secondary data, such as temperature, 
supply voltage or operating time, allows for predictive maintenance and thus optimum machine availability. 
 

6.1 

Device Status 

Parameter name 

Short Description 

Rights 

Unit / Allowed 
values 

Device Status 

Indicates if the sensor is 
working properly 

ro 

0=Device is OK 
2=Out of 
Specification 
4=Failure 
 
 

Detailed Device Status 

 

ro 

 

 

6.2 

Device Temperature 

An integrated temperature sensor allows to track the internal temperature of the sensor. 
Please be aware that compared to the ambient temperature the indicated values are higher due to the 
internal heating of the sensor.  
The temperature may also vary due to mounting conditions and due to the electric load connected to the 
output.  
 

Parameter name 

Short Description 

Rights 

Unit / Allowed 
values 

Device Temperature.Current 

 

ro 

 

Unit Selection.Temperature 

Choice of temperature unit 
(Default: °C) 

rw 

°C, °F, K 

 
 
 
 

 

Содержание O200



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды