Baumer O200 Скачать руководство пользователя страница 12

Страница: 12 / 34

en_BA_O200_IO-Link_V1.docx

12/34

Baumer Electric AG

15.08.2018/

Frauenfeld, Switzerland

4.3.2

SSC Configuration

4.3.2.1

Switching Mode

Figure 7

Single Point Mode (O200.G, O200.R)

A single setpoint (SP1) is defined at which the
sensor switches.

Figure 8

Window Mode (Only O200.G)

The sensor switches withing a range defined by two
different setpoints (SP1 and SP2)

Figure 9

Single Point Mode SmartReflect (O200.S)

A single setpoint (SP1) which represents the
position of the reference background.

Parameter name

Short Description

Rights

Unit / Allowed values

SSC1 Config.Mode

Selection of the switching mode

Disabled

Single Point

Window
(Only O200.G)

4.3.2.2

Channel Logic

Allows to change the output logic from Normally Open (NO, Normal) to Normally closed (NC, Inverted).

Single Point Mode Window Mode

Figure 10

«Normal» or NO setting

The

output is high

, when the object is

within the range defined by the setpoints.

The

output is low

when the object is not

present our outside of the range defined by
the setpoints

Figure 11

«Inverted» or NC setting

The

output is high

when the object is not

present our outside of the range defined by
the setpoints

the

output is low

, when the object is within the

range defined by the setpoints

Parameter name

Short Description

Rights

Unit / Allowed values

SSC1 Config.Logic

Changes the Logic from NO to NC

Normal (NO)

Inverted (NC)

Содержание O200



































Результаты поиска

Содержание O200

Отзывы:

Бренды по названию

Популярные бренды

Baumer O200, Инструкция по эксплуатации

Результаты поиска

Содержание O200

Отзывы:

Бренды по названию

Популярные бренды