Bauer Rainstar TX Plus E Скачать руководство пользователя страница 87

Страница: 87 / 92

Operating manual for

BAUER RAINSTAR series

TX Plus

24 TROUBLESHOOTING

FAULT

CAUSE

REMEDY

PE-pipe cannot be pulled off.

Gear shift lever in wrong position

Move to pull-off position.

Brake bank sticking on the brake
drum.

Loosen brake band.

PE-pipe retraction stops before
final shut-off activated.

Turbine blocked by foreign object. Remove foreign object.

Pressure drop in supply line.

Check pumping station and water
connection at the hydrant.

Overwinding

PE-pipe

actuates

the safety shut-off.

Adjust the winding mechanism.

Repair broken winding chain.

Final shut-off activated but the
shut-off valve does not close.

Values set for shut-off valve
actuation are not correct.

Adjust setting according to
instructions.

Thin plastic hose of shut-off valve
is blocked up or broken.

Replace the plastic hose.

The reel overwinds during pull-
off or the PE-pipe windings
become loose.

Tractor stopped abruptly.

Slow down gradually.

No oil in the change-speed
gearbox.

Refill oil.

Retraction speed varies from
one PE-pipe layer to the next.

Varying ground conditions.

Adjust speed control system to
the ground conditions (Change
rod position on the lever of the
layering mechanism. )

The desired retraction speed is
not reached.

Incorrect

transmission.

Select correct V-belt and
transmission.

Sprinkler nozzle blocked.

Remove foreign object.

General: compare connecting pressure and water flow with
performance chart values.

Cart is not lifted

Wrong gearbox transmission

Select correct V-belt and drive
transmission.

Содержание Rainstar TX Plus E





























































































Результаты поиска

Содержание Rainstar TX Plus E

Отзывы:

Bauer Rainstar TX Plus E, Руководство по эксплуатации, Страница: 87 / 92

Результаты поиска

Содержание Rainstar TX Plus E

Отзывы: