manualshive.com logo in svg

Bauer Rainstar TX Plus E, Руководство по эксплуатации, Страница: 70 / 92

Поделиться
Скачать
Bauer Rainstar TX Plus E Скачать руководство пользователя страница 70

 
 

Operating manual for 

BAUER RAINSTAR

 

Series TX Plus 

62 

19.6  SHUT-OFF FRAME (14) ADJUSTMENT 

 
In the 

operating position

 the distance between shut-off frame (14) and reel (18) X = 10 mm. 

 

Shut-of position: 

Hook up the cart lift bracket (15) with the locking hook (16). Screw down the setscrew (17) to the cart lift bracket 
(15) and turn it in until a spacing “X“ (see chart) results between the shut-off frame (14) and the outer reel 
diameter (18). Screw down the second setscrew (17) to the cart lift bracket.  Lock the setscrews (17). 
 
 

Basic unit 

X 

65 TX Plus 

35 

75 TX Plus 

40 

85 TX Plus 

45 

90 TX Plus 

45 

 
 
 
 
 
 
 
 
 
 
 
 
Grease gliding planes! 
 
 
 
 
 
 
 

19.7  SHUT-OFF ROD ADJUSTMENT (20) 

 

Switch into 1

st

 gear.  (Position “I).  Screw 

down the adjusting nuts (21) to the shut-off 
frame (14) and turn them in until shut-off is 
actuated. Lock the adjusting nuts (21)!  
       

 
 
 
 
 
 
 
 

 

 
 
 

65 TX
85 TX

90 TX

75 TX

14

15

16

17

18

Gleitfäche fetten !

X

14

18

Gleitfäche fetten !

20

21

Grease gliding planes! 

Содержание Rainstar TX Plus E





























































































Отзывы:

Нет отзывов