manualshive.com logo in svg

Bauer Rainstar TX Plus E, Руководство по эксплуатации, Страница: 19 / 92

Поделиться
Скачать
Bauer Rainstar TX Plus E Скачать руководство пользователя страница 19

 

 

Operating manual for 

BAUER RAINSTAR series

 TX Plus 

11 

 

 

Move the gear-shift lever to the „PE-pipe pull-off“ position. A 
spring presses the lever up and locks it.   

 

 

5.2.3  PE-PIPE PULL-OFF  

 

 

 

Pick up the draw-out hook with the toolbar and start pulling 
the cart . 

 

 

 

The standard wheel cart or the asymmetric wheel cart need 
not be hoisted (therefore 1 draw-out hook is sufficient).    
Pull-off speed:  do not exceed  5 km/h! 

 
Do not stop abruptly.  Always slow down gradually at an intermediate stop in the field or at the end of the pull-off. 
Stop pulling off the pipe when the white marking line becomes visible on the reel. 

 

 

 
If the PE-pipe has been exposed to the sun for a longer period or if its surface 
temperature rises above 35 °C for some other reason you must let water run 
through the pipe to cool it off before the unwinding or retraction procedure.  
 

 

WARNING!

 

Содержание Rainstar TX Plus E





























































































Отзывы:

Нет отзывов