Bauer Rainstar TX Plus E Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 92

Bauer Rainstar TX Plus E Скачать руководство пользователя страница 80

Operating manual for

BAUER RAINSTAR

Series TX Plus

72



Retract the pipe at the lowest possible PTO speed - start slowly and smoothly
and avoid jerks.



Max. PTO speed = 540 rpm



Avoid strain by excessive articulation of the PTO shaft.



If the PE-pipe is covered with mud it should be loosened and set free to reduce
the tension load before rewinding it.



You can release the PE-pipe and lift it off the ground by tying around a hemp
rope or a fabric belt and pulling it along the pipe.



If the soil is deep and heavy the PE-pipe must be wound up more slowly to
make sure that the permissible loads on PE-pipe and RAINSTAR are not
exceeded.



If you disengage the PTO shaft during PE-pipe retraction, make sure that the
pipe reel stands still when you re-engage the PTO shaft.(Slacken the PE-pipe).
Double motion may cause severe damage!



When driving the reel with the PTO the automatic shut-off system is inactive.
Therefore you must stop the PTO shaft in time and wind up the end of the PE-
pipe with the hand wheel. This will prevent damage to cart, shut-off system,
gearbox, etc.

21.6 SPEED CONTROL

Speed control with ECOSTAR - see page 18
Mechanical speed control - see page 34

21.7 TACHOMETER

Optional equipment for systems with mechanical speed control – see page 12

WARNING!

«
...
78
79
80
81
82
...
»

Содержание Rainstar TX Plus E





























































































Отзывы:

Нет отзывов