manualshive.com logo in svg

Bauer Rainstar TX Plus E, Руководство по эксплуатации, Страница: 74 / 92

Поделиться
Скачать
Bauer Rainstar TX Plus E Скачать руководство пользователя страница 74

 
 

Operating manual for 

BAUER RAINSTAR

 

Series TX Plus 

66 

 

 

Pick up the draw-out hook with the toolbar and pull off the 
cart.    

 

Pull-off speed: do not exceed 5  km/h! 
Do not stop abruptly.  Always slow down gradually at an intermediate stop in the field or at the end of the pull-
off.  Stop pulling off the pipe when the white marking line becomes visible on the reel.   
 

 

 

If the PE-pipe is to be pulled off in a wide bow, make sure that it is pulled in a 
straight line of about 80 to 100 m first (90° angle to the reel) and then in a wide bow.  

 

 

 

 

If the PE-pipe has been exposed to the sun for a longer period or if its surface 
temperature rises above 35 °C for some other reason, you must let water run 
through the pipe to cool it off before the unwinding or retraction procedure.  

 

 

 

 

Couple the pressure hose.  Open water supply.   

 
Put the gear shift lever into the correct position.     

 

 

 

 

TX 20

1

8

--

20

m / h

2

16

--

32

m / h

3

28

--

50

m / h

4

> 45

m / h

 

 

 

 

 

 

 

 

WARNING!

 

Warning!

 

Содержание Rainstar TX Plus E





























































































Отзывы:

Нет отзывов