![background image](http://html1.mh-extra.com/html/battioni-pagani/kps-490/kps-490_instruction-manual-for-use-and-maintenance_2708431026.webp)
Instruction Manual
for WPT, KTS, KPS, KTM, WSM series use and maintenance
pag. 50
8) fix the hydraulic motor transmission coupling to the anterior pin by the
screw located inside the pin;
8) assemble the locknut to fasten the pinion;
9)
Fix hydraulic motor support to the coupling flange;
9) put the gear into the bearing housing;
10)
Mount the hydraulic motor on its support with screws;
10) replace box cover gasket;
11)assemble multiplier box cover;
KPS SERIES
…/M - MA …/G - GA
…/K - KA
…/P
…/D
…/H
1) Disassemble the Seeger ring.
1) Disassemble the Seeger ring.
1) Disassemble the Seeger ring.
1) Disassemble the Seeger ring.
2) Disassemble the bearing
2) Disassemble the bearing
2) Disassemble the bearing
2) Disassemble the bearing
3) Replace flange gasket;
3) Replace flange gasket;
3) Replace flange gasket;
3) Replace flange gasket;
4) Insert the cotter pins included
in the body
5) Fasten the multiplier box to
the body by means of screws
tightened at 45 ÷ 55 Nm
4) Insert the cotter pins included
in the body
4) Insert the cotter pins included in
the body
5) Fasten the multiplier box to
the body by means of screws
tightened at 45 ÷ 55 Nm
5) Fasten the flange to the body
by means of screws tightened
at 45 ÷ 55 Nm
5) Fasten the flange to the body
by means of screws tightened
at 45 ÷ 55 Nm
5) Fasten the flange to the body by
means of screws tightened at
45 ÷ 55 Nm
6) Assemble the bearing on the
moltiplier box by using a
buffer and insert the com-
pensating ring and insert the
Seeger ring;
6) Assemble the bearing on the
flange by using a buffer and
insert the compensating ring
and insert the Seeger ring;
6) Assemble the bearing on the
flange by using a buffer and
insert the compensating ring
and insert the Seeger ring;
6) Assemble the bearing on the
flange by using a buffer and
insert the compensating ring
and insert the Seeger ring;
7) Insert the spacer and assemble
the pinion on the shaft
7) Reassemble the front
cover on the flange.
7) Reassemble the front cover on
the flange.
7) Reassemble the hydraulic motor
support.
8) Assemble the fastening locknut
of the pinion;
8) Remove the centring pins from
the body
8) Reassemble the shrunk-on
8) Remove the centring pins from
the body.
9) Insert the gear in the bearing
housing
9) Remove the centring pins from
the body.
10) Assemble the box cover;
11) Fill the multiplier box with oil
up to the level.
12) Remove the centring pins
from the body.
WPT SERIES
1) Replace the front flange gasket;
…/M - MA
…/P
…/D
2) fix the gearbox to the coupling flange with
screws;
2) bring the front flange up to the pump body,
positioning it in alignment with the clamping
holes;
2 ) bring the front flange up to the pump body, posi-
tioning it in alignment with the clamping holes;
3) fit pinion to the rotor pin;
3)
tighten the clamping screws of the front
flange to the body;
3) tighten the clamping screws of the front flange
to the body;
4) fit the self-locking nut for fixing the pinion;
4)
attach the front cover to the flange with
clamping screws;
4) attach the front cover to the flange with clamp-
ing screws;
5) insert the gear in the bearing seat;
5)
connect the lubrication tube by screwing it
to the connecting piece placed on the front
cover;
5) connect the lubrication tube by screwing it to the
connecting piece placed on the front cover;
6) replace the gearbox cover gasket;
6) insert the pulleys on the front pin, fixing them
with the key;
7) fix the gearbox cover;