Basler BE1-51/27R Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 102

background image

4-16

BE1-51/27R - Installation

Feeder

BE1-51 (51)

(Breaker F)

0.5 to 12 A
Very inverse timing
800/5 CTs
No instantaneous
Pickup set to 6 A
Time Dial set to 08

Phase Directional

BE1-67, (67)

Breaker L)

Definite timing (B3)
0.5 to 12 A
3000/5 CTs
Pickup set to 0.5 A
Time Dial set to 02

Generator Reactance

Subtransient

0.18

(Per Unit)

Transient

0.25

Steady state

1.5

Figure 4-16. Setting Example

Downstream current in Table 4-1 is the current in the downstream relay with which the BE1-51/27R elements
must coordinate. The currents are the changes resulting from the fault assuming a driving point voltage of 11
kV. Actual currents will be the sum of the table values plus the pre-fault load currents. Transient level currents
are based on use of the generator transient reactance. Steady-state level currents are based on use of
generator steady-state reactance and assuming no generator regulator boost. Note that the table values apply
for 3-phase faults. Transient level currents in generators for a phase-to-phase fault will be about equal to the
3-phase current values. Steady-state level currents in the generators will be higher for a phase-to-phase fault.

«
...
76
77
78
79
80
...
»

Содержание BE1-51/27R







































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-51/27R

Бренд: West Control Solutions Страницы: 59

Бренд: Schweitzer Engineering Laboratories Страницы: 12

Бренд: jablotron Страницы: 2

Бренд: F&F Страницы: 3

Бренд: F&F Страницы: 4

Бренд: F&F Страницы: 2

Бренд: F&F Страницы: 2

Бренд: F&F Страницы: 6

Бренд: Chromalox Страницы: 4

Бренд: Eaton Страницы: 8

Бренд: Eaton Страницы: 64

GreenMAX R1616-1CB

Бренд: Leviton Страницы: 2

Бренд: Viessmann Страницы: 4

Бренд: GE Страницы: 18

Бренд: Seg Страницы: 26

HighProTec Series

Бренд: Woodward Страницы: 23

Big Boy 00-00507-512

Бренд: Intellitec Страницы: 4

uni-line Series

Бренд: Deif Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды