Basler BE1-51/27R Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 102

background image

BE1-51/27R - Tests And Adjustments

5-15

Step 10. Set the front panel INST 1 (NEUTRAL) control to a position approximating the desired neutral

instantaneous 1 overcurrent pickup point for the relay.

Step 11 Apply current to the relay.

Step 12 Rapidly increase the overcurrent input to the relay until the instantaneous output relay just

energizes. Note the test set overcurrent threshold reading on the ammeter.

Step 13. Remove the input current.

Step 14. Reset the INST TARGET (if present).

Step 15. If the overcurrent threshold reading from Step 13 was too high or low, adjust the front panel INST

1 (NEUTRAL) control CCW to lower (or CW to raise) the Neutral Instantaneous 1 Overcurrent
Pickup Point. Repeat Steps 9 through 14. If NOT, proceed to the next test.

INST 2 Control Setting

For this adjustment, repeat INST 1 control setting, but substitute instantaneous 2 output terminals (11 and
12) and the front panel INST 2 controls. Because neutral sensing does not apply to this pickup point, ignore
Steps 9 through 15.

«
...
97
98
99
100
101
...
»

Содержание BE1-51/27R







































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-51/27R

Бренд: Woodward Страницы: 119

Бренд: Tense Страницы: 2

Бренд: Steren Страницы: 20

Бренд: Pilz Страницы: 16

Бренд: Littelfuse Страницы: 82

Бренд: GE Страницы: 23

Бренд: GE Страницы: 36

Бренд: GE Страницы: 42

Бренд: GE Страницы: 42

Бренд: Eaton Страницы: 4

Бренд: Federal Signal Corporation Страницы: 20

Бренд: F&F Страницы: 7

Бренд: Ampcontrol Страницы: 29

Бренд: KAEL Страницы: 10

Бренд: Eurotherm Страницы: 42

Бренд: VAMP Страницы: 232

Бренд: ZIEHL Страницы: 8

Silent Knight SK-Relay

Бренд: Honeywell Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды