Basco Infinity 1413 Скачать руководство пользователя страница 10

Страница: 10 / 11

INSTALLATION INSTRUCTIONS – ACCESSORIES

Combination Door Pull and Towel Bar Installation Instructions

There are eleven hardware components for Combination Door Pull and Towel Bar mounting: Six 1-

1/4” style washers; one towel bar; one pull; two end caps with threaded studs; one stud head screw. In

addition to these hardware parts, there are six clear gaskets th at act as a buffer between the hardware

and the glass.

STEP 1

Take the stud head screw and sleeve a 1-

1/4” style washer on it. Now take both end caps with a

stud protruding and sleeve a 1-1/4” style washer on

them. Sleeve a clear gasket on each of the screws.

STEP 2

The towel bar will be mounted first. Take

the stud head screw with the washer and gasket attached,

and from the inside of the enclosure push the threaded

portion through the top hole in the glass on the strike

side of the door. Place a clear gasket, then a 1-1/4” style

washer over the stud head screw on the outside of the

glass door. Now thread the stud head screw into the

towel bar and tighten. On the other end of the towel bar

(on the hinge side), push one of the end caps with the

stud protruding through the hole. Now place a clear

gasket, then a 1-1/4” style washer over the threaded stud

on the outside of the glass door. Thread the end cap into

the towel bar and tighten by hand. Tighten both

components down, the stud head screw with a

screwdriver, and the end cap by hand.

STEP 3

The towel bar is now complete and it is time to mount the pull portion. From outside

the enclosure, push the end cap with the stud protruding through the bottom hole of the door. First

place a clear gasket, then a 1-1/4” style washer over the threaded stud on the inside of the glass door.

Now thread the stud into the small threaded opening of the pull. Do not tighten this end of the pull

down at this time. Place the end of the pull with the large hole and the set screw over the stud head.

Now tighten the end cap by hand as tight as possible. Use the Allen wrench provided to tighten the set

screw on the pull to the stud head screw.

J Exterior handle (1)

T Towel bar (1)

L SC4584 Metal washers (6)

M SC4585 Large clear discs (6)

N SC4586 Small clear discs (6)

O SC4587 Glass hole sleeve (3)

P SCR1588 Stud screws (3)

QCI0029 REV. 1

Page 10 of 11

Certified 07/06/05

Содержание Infinity 1413












Результаты поиска

Содержание Infinity 1413

Отзывы:

Похожие инструкции для Infinity 1413

Бренды по названию

Популярные бренды

Basco Infinity 1413, Руководство по установке

Результаты поиска

Содержание Infinity 1413

Отзывы:

Похожие инструкции для Infinity 1413

Бренды по названию

Популярные бренды