Barco RLM G5i Performer R9010320 Скачать руководство пользователя страница 110

Страница: 110 / 150

12. Image Files Menu

Advanced edit

Comb filter

Off

AGC hold interval

Short

Long

Sync locking

Slow

Fast

Sharpness

Coarse

Fine

Image 12-8

video signal

frame blanking

egalisation

Image 12-9

HI AGC Hold interval

The

Comb filter

is by default enabled.

The

AGC hold interval

is the time interval in which the AGC is inhibited (AGC hold = no update in video amplitude measurement),

the advanced parameter allows to choose a short or long hold interval.

A long AGC hold interval eliminates Macrovision

disturbances since the AGC is hold during a long interval, thus reducing the

probability to encounter a Macrovision

pulse.

The

sync locking setting

is recommended for poor video signals (ex: poor TV signals).

Sharpness

adjustment can be chosen to be coarse or fine.

It is recommended to use the default values.

12.6.4 Advanced Data settings

Overview

When a data source is selected, the

advanced

button enables the advanced settings for a data source.

Advanced edit

VCO range

PLL Cpmp

Clamp position

Clamp width

Horizontal sync polarity

Determined by ADC
Active low
Active high

Input format

RGB
PR/Y/PB
HDTV-PR/Y/PB

Image 12-10

video info

Image 12-11

Hs horizontal sync pulse
a

active low

active high

The

VCO range

setting determines the frequency range of the VCO (Voltage Controlled Oscillator).

The

Cpmp

(Charge pump current) sets the low pass filter current.

Both VCO range & Cpmp are set by the image file, changing these settings is only indicated in for special purposes.

The

horizontal sync polarity

setting can be useful in case of a bad shaped edge, one can choose between the leading (active low)

or trailing (active high) edge.

The input format settings are used to "tell more" about the signals connected on the BNC’s, it completes the information in the source
selection menu.

- RGB is selected by default and means that an RGB signal is connected to the BNC’s

- PR/Y/PB must be selected whenever:

108

R5976815 RLM G5I PERFORMER 02/06/2006

Содержание RLM G5i Performer R9010320























































































































































Результаты поиска

Содержание RLM G5i Performer R9010320

Отзывы:

Похожие инструкции для RLM G5i Performer R9010320

Бренды по названию

Популярные бренды

Barco RLM G5i Performer R9010320, Руководство пользователя

Результаты поиска

Содержание RLM G5i Performer R9010320

Отзывы:

Похожие инструкции для RLM G5i Performer R9010320

Бренды по названию

Популярные бренды