Cover can be flipped around 180
degrees to hide LEDs from front
straight-on view if desired.
Cover can be removed and painted to match
color of wall. Do not paint the sides, top or
bottom. Warranty will be voided.
Cover of MD2-RCA can easily be removed
by pulling cover at the 2 side indents (1).
Unit can be securely screwed into wall
outlet faceplate using either hole (2)
indicated (screw is included).
1
2
1690 Corporate Circle, Petaluma, CA 94954 • 800-472-55555 • 707-283-5900 • Fax 707-283-5901 • www.panamax.com
INSTALLATION INSTRUCTIONS MD2-RCA
Bottom view
of MD2-RCA
Top view of product
INS00878-A 1/10
CUSTOMER SUPPORT:
800-472-5555
OPTIONS FOR SECURITY MOUNTING & FRONT COVER FACEPLATE
FEATURES
LINES IN
FROM
MD2-RCA
LEFT SIDE
OUTLET
GROUND
PLUG OUT
RIGHT
SIDE
OUTLET
GROUND
PLUG
DOWN
Side views of product
1.
Turn off the equipment you are plugging into the MD2-RCA.
2
.
Plug the surge protector into the wall outlet. A red
"Line Fault"
light indicates
an improperly wired outlet that must be checked by a qualified electrician.
3.
If the blue
"Power On Protection OK"
light is on, plug your equipment into
the AC outlets on the surge protector.
The protection circuitry on the MD2-RCA and MD2-RCA MODULE only
work if the signal lines are connected properly.
4.
Connecting signal lines to the MD2-RCA: The lines coming from the MD2-RCA
MODULE plug into the “IN” jacks. Lines from the “OUT” jacks then connect to the
equipment being protected.
4.5
Connecting signal lines to the MD2-RCA MODULE: The lines coming from the
MD2-RCA plug into the “IN” jacks. Lines from the “OUT” jacks then connect to
the source equipment in the rack.
5.
To mount module to rack, slide zip ties through slots on back. Wrap and tie
around leg on equipment rack.
6.
Turn the connected equipment ON and
check for power and correct operation.
Panamax surge protectors and the connected equipment must be indoors in a dry location and in the same building. Do not install any
Panamax product near heat emitting appliances such as a radiator or heat register. Do not install this product where excessive
moisture is present; for example, near a bathtub, sink, pool, basement floor, fish tank, etc.
It is not uncommon for a building to be improperly grounded. In order to protect your equipment, and validate the warranty, Panamax
products must be plugged into a properly grounded 3-wire outlet. Additionally, building wiring and grounding must conform to
applicable NEC (USA) or CEC (Canada) codes for the Panamax warranty to be valid.
Do not use 2-prong adapters with this product. If an extension cord is required, use only Panamax #GEC1410. If at any time your
surge protector indicates a Line Fault, call your electrician to correct the building wiring.
POWER ON /
PROTECTION OK- (blue)
normally ON - indicates
that the power is on,
surge protector is
functioning properly,
and all connected
equipment is protected.
LINE FAULT INDICATOR-
(red) - If lit red, indicates
an improperly wired outlet.
AC outlets are turned 90 degrees from one
another to accommodate different style
plugs or transformers.
Properly Connecting Your Surge Protector
To completely protect your equipment from power surges, every wire leading into or out of the equipment you want to protect must be connected to the
appropriate Panamax surge protector. Damaging lightning and power surges can get into your system through any AC power or signal line (phone lines,
grounding wires, coax cables, modem cables, etc.) connected to your electrical equipment.
The $100,000 Connected Equipment Protection Policy is invalid if any wire leading into or out of the equipment is not properly connected to the
appropriate Panamax surge protector(s). The surge protector must also be plugged into a properly wired and grounded outlet. Please see the warranty
for details or contact the Panamax Customer Relations department with questions.
Overview
Make sure you have the right surge protector to protect your electronic equipment. Panamax makes protectors for almost every type of electronic
equipment. Surge protectors that may look identical from the outside can be very different on the inside. It is very important to use the surge protector
designed for your application. Two-outlet surge protectors are not designed for use with systems having more than two AC powered components.
Panamax offers a wide range of surge protectors designed for use with larger systems. If you have any questions about which product is best for your
applications, please see our web site www.panamax.com or contact Panamax Customer Relations at 800-472-5555 (7:30 a.m. – 4:30 p.m. PST).
Limited Lifetime Product
Warranty*
$
100,000
Limited Connected
Equipment Protection Policy*
MD2-RCA
MD2-RCA MODULE
GROUND WIRE CONNECTED TO
GROUND LUG ON BACK OF
PANAMAX COMPONENT
IN RACK
LINES OUT TO
SOURCE
COMPONENT
LINES IN FROM
MD2-RCA MODULE
LINES OUT TO EQUIPMENT
MD2-RCA
MODULE
MODULE MOUNTS
VERTCAL OR HORIZONTAL
POWER ON
PROTECTION OK
LINE
FAULT
TYPICAL INSTALLATION
IMPORTANT SAFETY POINTS
*See documentation on back side for details.
MD2-RCA
PROPERLY GROUNDED
AC OUTLET
SIGNAL
LINE IN
REMOTELY
LOCATED
POWERED
SUBWOOFER
OR VIDEO
DISPLAY
AC LINE
SIGNAL
LINE OUT
GROUND WIRE CONNECTED
TO PANAMAX COMPONENT
GROUND LUG
EQUIPMENT
RACK
IN IN IN
OUT OUT OUT
IN IN IN
OUT OUT OUT
SIGNAL
LINE IN
MD2-RCA MODULE
STRAPPED TO RACK LEG WITH ZIP TIES (INCLUDED)
SIGNAL LINE OUT
TO SOURCE
COMPONENT
CONNECTED TO
SOURCE COMPONENT
AC LINE
