background image

A

Aligning with adjustable height frame

1. Set the frames to the required height.

Use a 10 mm socket spanner for the

4 screws.

Caution:
Make sure each frame is attached with all 4 screws.

2. Adjust the adjustable feet. Use a 13 mm fork spanner.
3. Make sure that the appliance is installed horizontally. Use a spirit level.

5.3.3

Connect the flue gas pipe

The appliance can be connected to steel pipes, double-walled insulated stainless steel

flues and flexible stainless steel flues with an outside diameter of 250 mm.

Caution:
• During operation of the appliance the outer side of the flue system

becomes hot. Refer to the installation instructions of the flue system for

safe installation. Follow these instructions with regard to safe distances to

combustible material.

If the appliance is installed on an unlined, masonry flue with a large diameter, consider

using a flue lining system to improve the performance of the appliance.
It is possible to connect the appliance on a flue with an inner diameter of minimum

200mm. Use a correct adapter on the flue connector.

Important:
If the appliance is fired with the door closed at all times, it is possible to use a

flue with a diameter of 200 mm. If not, use a flue with a diameter of 250 mm

1. Connect the flue to the flue gas connection on the appliance. If necessary use a steel

flue adaptor.

2. If a flexible stainless steel flue is used, secure the flue connection with 2 clamps.
3. If the flue is connected to an existing (masonry) chimney, make sure that the gap

between the flue and the existing chimney is sealed, with ceramic wool or any other

applicable component (ask your flue system supplier for advice)

4. Make sure that all mechanical connections of the flue system are correctly used.
5. Make sure that all of the flue system is gas-tight,
6. Insulate any non-insulated pipes with ceramic insulation wool. Refer to 

5.3.6

 for the

material requirements.

Installation

Evolux 100-45

19

Содержание Evolux 100-45

















































Отзывы: