manualshive.com logo in svg

Bandit 2290, Инструкция по эксплуатации и каталог запасных частей

Поделиться
Скачать
Bandit 2290 Скачать руководство пользователя страница 99

Bandit

95

Copyright 8/19

MODEL 2290

BASE COMPONENTS

2290 TRACK BASE

LOCATION 

PART NUMBER 

DESCRIPTION

** Components vary with engine options, refer to check sheet or machine S/N.

Nuts, bolts, washers, and all other components can be ordered by physical description.

NOTICE

1.   

249-1000-95 

Base Assembly

2.   

900-1921-85 

Drum Bearing Kit

3.   

259-2001-06 

Base/Shaft Cover Assembly 

4.   

See Page 101 Anvil

5.   

See Page 97 

Drum Head Assembly

6.   

911-1001-88 

Vent Cover

7.   900-4908-29 

Vent Cover Plastic Knob

8.   

937-300007 

Air Vent Cover 

 

9.  a. 

259-3000-52 

Base/Chipper Shaft Slot Cover (Drive Side) 

b. 

259-3002-37 

Base/Chipper Shaft Slot Cover (Radiator Side)

10.  

249-2002-05 

Hinged Hood Assembly

11.  

249-3001-56 

Knife Access Door Plate

12.  

249-2001-54 

Top Belly Band Front Half (Track)

13.  

249-2001-75 

Upper Belly Band Assembly w/Breakers

14.  

See Page 96 

Stick Breaker Assembly (Single Replace)

15.  

        ** 

Drive Sheave

16.  

        ** 

Drive Bushing

17.  

        ** 

Chipper Belt

18.  

        ** 

Beltshield Assembly

19.  

        ** 

Driven Bushing

20.  

        ** 

Driven Sheave

Содержание 2290









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды